manualshive.com logo in svg

Sharp MX-M1054, Technical Handy Manual, Page: 13 / 76

Share
Download
Sharp MX-M1054 Technical Handy Manual Download Page 13

 

Density & Gradation Adjustment

 

 

SHARP

 

Document Solution Centre

 

13 

 

 

Automatic Grey Balance Calibration - FACTORY MODE 

 

Note:  When adjusting grey balance adjustment before or after routine maintenance, always use the  
 

recommended paper (Mondi 90gsm or equivalent) for optimum image quality. 

 

HIGH DENSITY PROCESS CONTROL:

 

 
 

[Execute] 

 

   

  Sim 44-06 

 

 

HALFTONE PROCESS CONTROL:

 

 
 

[Execute] 

 

   

  Sim 44-26 

 

 

GREY BALANCE ADJUSTMENT:

 

 

 

 

 

   

  Sim 46-74 

[Engine & Printer] 

 

 

FACTORY MODE 

 

Place printed test pattern onto glass for both Copy &  

 

Printer  modes.

 

 
 

Manual Colour Calibration – SERVICE MODE 

 

HIGH DENSITY PROCESS CONTROL:

 

 
 

[Execute] 

 

   

  Sim 44-06 

 

 

HALFTONE PROCESS CONTROL:

 

 
 

[Execute] 

 

   

  Sim 44-26 

 

 

GREY BALANCE ADJUSTMENT:

 

 

 

 

 

   

  Sim 46-74 

[Engine & Printer] 

 

 

SERVICE MODE 

 

Place printed test pattern onto glass for both Copy & 

 

Printer  modes.

 

 

GREY BALANCE MANUAL ADJUSTMENT:

 

 

 

 

 

   

  Sim 46-21 

[for Engine] 

 

   

  Sim 67-25 

[for Printer] 

 

Adjust K (17 points) for Copy & Printer Modes.

 

 

 

Summary of Contents for MX-M1054













































































Reviews:

No comments