Sharp MX-M1054 Technical Handy Manual Download Page 43

Page: 43 / 76

Firmware & Print Driver Revision

SHARP

Document Solution Centre

Engine Firmware:

Firmware ROM

ICUM MAIN

02.00.h2

ICUM BOOT

02.00.h2

ICU1 MAIN

02.00.h2

ICU1 BOOT

01.01.h2

PCU

02.00.h2

SCU

01.00.h2

SPF

01.00.h2

UI CONTENTS

02.00.h2

LCC

01.00.S1

LCC A3 [MX-LCX3N]

01.01.S1

LCT [MX-LC13]

01.07.S1

INSERTER [MX-CF11]

01.03.01

FOLDING UNIT [MX-FD10]

01.01.01

FINISHER [4K MAIN]

01.09.01

SADDLE

01.05.01

TRIMMER [MX-TM10]

01.01.01

STACKER UNIT [MX-ST10]

01.03.02

PUNCH [4K MAIN]

01.01.01

FAX MAIN [MX-FX11]

01.01.G1

DATA SECURITY KIT [MX-FR38U]

TBD

ACU [MX-EB11]

04.00.A1

WATERMARK

01.00.h2

E-MANUAL

01.30.h2

Print Driver:

Driver

Windows OS x86

XP, 2008, Vista, 7

Windows OS x64

XP, 2008(R2), Vista, 7

PCL6

02.00.10.13 [WHQL]

02.00.12.13 [WHQL]

02.00.10.13 [WHQL]

02.00.12.13 [WHQL]

PPD

1.3.0.0 [WHQL]

PC-Fax

3.7.18.4

TWAIN

3.01.004.000 [WHQL]

XPS **

01.03.37.01 [WHQL]

Note: ** XPS driver supports Windows Vista only.
For the latest Firmware and Print Driver version(s),

please refer to the SHARP Support Website.

Summary of Contents for MX-M1054













































































Search results

Summary of Contents for MX-M1054

Reviews:

Sharp MX-M1054, Technical Handy Manual, Page: 43 / 76

Search results

Summary of Contents for MX-M1054

Reviews: