manualshive.com logo in svg

Sharp MX-M1054, Technical Handy Manual, Page: 37 / 76

Share
Download
Sharp MX-M1054 Technical Handy Manual Download Page 37

 

MX-EB15 Mirroring Kit

 

 

SHARP

 

Document Solution Centre

 

37 

 

 

When the mirroring kit is installed, the two HDD units are named HDD1 (Standard Machine HDD) and HDD2 
(Mirroring Kit HDD). The status of the Mirroring Kit is displayed by one of the following UI Icons within the 
operation panel:- 
 

Mirroring Kit is installed. 

 

Mirroring Kit / HDD Trouble. 

 

Mirroring Kit / Rebuilding - 

Copying the whole contents of one HDD to the other HDD.

 

 
 
Troubleshooting: 

 

Use SIM62-20 to check the HDD status, and refer to the following tables to confirm the relation between 
the HDD status and possible remedy :- 
 
Status & Trouble when             is displayed:- 
 

SIM 62-20 

HDD2 

OK 

NONE 

REBUILDING 

ERROR 

TROUBLE 

HDD1 

OK 

– 

A 

– 

A 

A 

NONE 

A 

– 

– 

– 

– 

REBUILDING 

– 

– 

– 

– 

– 

ERROR 

A 

– 

– 

– 

– 

TROUBLE 

A 

– 

– 

– 

– 

 
 
Status & Trouble when E7-03 error message is displayed:- 
 

SIM 62-20 

HDD2 

OK 

NONE 

REBUILDING 

ERROR 

TROUBLE 

HDD1 

OK 

B 

B or C 

B 

B 

B 

NONE 

B or C 

C 

C 

C 

C 

REBUILDING 

B 

C 

F 

F 

F 

ERROR 

B 

C 

F 

F 

F 

TROUBLE 

B 

C 

F 

F 

D or E 

 
 
 

Cont’d 

 

 

 

Summary of Contents for MX-M1054













































































Reviews:

No comments