Sharp MX-M1054 Technical Handy Manual Download Page 16

Page: 16 / 76

Maintenance

SHARP

Document Solution Centre

Interval Checklist

500k

1000k

3000k Process Section:

Replace Developer [MX-900GV]

Replace OPC Drum [MX-850GR]

Replace Developer Maintenance Kit [MX-900DK]:-

•

Doctor cover unit / DV seal.

•

DV side seal F.

•

DV side seal R.

•

DV box filter.

•

DV toner filter.

Replace Cleaning Blade Kit [MX-900CB]:-

•

Cleaning blade.

•

Side seal F.

•

Side seal R.

•

Sub blade.

•

Drum separation pawl x4

•

Duct sheet.

Relocate Drum Separation Pawl mounting position

Clean Before-Transfer Discharge Lamp.

Clean OPC Drum Surface Potential Sensor

Use Blow Brush or Dry Cloth – DO NOT CLEAN with Vacuum Cleaner

Replace Main Charge Kit [MX-900MK]:-

•

Charger wire x2.

•

Screen grid.

•

Charger cleaner.

•

Charger cushion.

•

Cleaner base guide.

Clean Main Charger Case

Replace Main Charger Case

[PCASZ0326FCZ1]

Replace Process Unit Blade Side Seal Front

[PSEL-0992FCZ1]

and

Rear

[PSEL-0991FCZ1]

Replace Ozone Filter Kit [MX-900FL] :-

•

Ozone filter

•

Outlet filter.

Sim 24-05

Clear Developer Print, Rotation & Day Counter

(only when Developer is replaced)

Sim 25-02

Toner Concentration Adjustment

(only when Developer is replaced)

Sim 24-04

Clear MAINTENANCE ALL Counter

Sim 24-04

Clear DRUM CRTG K Counter

(only when OPC Drum is replaced)

Sim 24-04

Clear DRUM BLADE K Counter

(only when Drum Cleaner Blade is replaced)

Summary of Contents for MX-M1054













































































Search results

Summary of Contents for MX-M1054

Reviews:

Sharp MX-M1054, Technical Handy Manual, Page: 16 / 76

Search results

Summary of Contents for MX-M1054

Reviews: