manualshive.com logo in svg

Sharp MX-M1054, Technical Handy Manual, Page: 10 / 76

Share
Download
Sharp MX-M1054 Technical Handy Manual Download Page 10

Initial Setup 

 

 

10 

SHARP

 

Document Solution Centre

  

 

 

 UNPACKING & LOCK REMOVAL 

 

 

Use Skid Slopes

 [UKOG-0367FCZZ]

 to remove device from shipping pallet. 

 

Operation Panel installation. 

 

Remove Tray Lift Lock Plates. 

 

Release Fusing Pressure. 

 

 DEVELOPER SET-UP 

 

 

Sim 25-02 

Auto Developer Adjustment - 

Select K. 

 

Toner Installation must be performed after Auto Developer Adjustment is 
completed. 

 

**For optimum image quality & performance, it is recommended to setup &    
    install developer at the customer site. 

 

 TONER INSTALLATION & REPLENISHMENT 

 

 

Install K Toner Cartridge. 

 

 PRODUCT ACTIVATION & FIRMWARE UPGRADE 

 

 

Activation of Optional Product(s):-  

System Settings – Product Key. 

 

Sim 22-05 

Check Firmware version(s):- 

Upgrade to latest version. 

 

 INITIAL SETUP  

 

 

Sim 21-01 

Maintenance Cycle Setting:- 

Set PM Counter = 500k, 

 

Sim 26-02 

LCC Installation (Paper Size).

 

 

Sim 26-06 

Machine Destination. 

 

Sim 26-35 

Set Multi Error Counter:- 

Set to 1 (Multi Count). 

 

Sim 26-52 

Non Printed Paper Counter Set-up. 

 

Sim 40-12 

Multi Purpose Tray (Tray 4) Adjustment/Calibration. 

 

Sim 55-03 

Process Mixed Original Printing for Duplex:- 
SSW 3-6, 

0 = Disable, 1 = Enable.

 

 

System Settings: Adjust Date/Time (Inc. Daylight Saving setting). 

 

Set cassette size by adjusting the guides in the cassette. 

 

Paper Size & Type Setting

:-

 System Settings – Paper Tray Settings. 

 

 PRINT ENGINE IMAGE SKEW 

 

 

Sim 64-02 

Image Writing Adjustment:- 

 

 

 

Select A=5, B=1, C=254, D=255, E=1, F=1, G=8. 

 

Summary of Contents for MX-M1054













































































Reviews:

No comments