Sharp MX-M1054 Technical Handy Manual Download Page 18

Page: 18 / 76

Maintenance

SHARP

Document Solution Centre

Interval Checklist

500k

1000k

3000k Transfer Section:

Replace Transfer Belt Kit [MX-900TT] :-

•

Transfer belt.

•

Transfer roller.

•

Transfer cleaning blade.

•

Ball bearing x4.

Replace Transfer Sub Blade

[UCLEZ0197FCZZ]

Sim 24-04

Clear TRANS BLADE Counter

(only when Transfer Belt Kit is replaced)

Sim 24-04

Clear TC BELT Counter

(only when Transfer Belt Kit is replaced)

DSPF:

Check/Clean DSPF Rollers - Replace when DSPF counter reaches 200k

Clean all DSPF sensors.

General:

Clean all optics, CCD, and white reference plate.

Paper Feed & Transport:

Replace Paper Dust Removal Kit [MX-900PD]

Check/Clean ALL Vertical & Transport Paper Guides, Transport Rollers
& Paper Path Sensors

Check/Clean ALL Vertical & Transport Paper Path Sensors & Double
Feed Detect Sensor (only use Blow Brush).

Check/Clean PF Rollers.
Replace when Individual Tray counter reaches 200k.

Replace Paper Feed Transport Roller 4

[NROLR1606FCZZ]

& Paper

Feed Transport Roller 3

[NROLR1607FCZZ]

when Tray3 or 4 counter

reaches 3000k.

Replace PS Roller

[NROLR1670FCZZ]

PS Follower Roller (Idle)

[NROLP1667FCZZ]

Replace PS Idle Gear

[NGERH1859FCZZ]

, PS Driver Gear

[NGERH1858FCZZ]

, PS Follower Gear

[NGERH1876FCZZ]

PS Gear

[NGERH1877FCZZ]

Replace Tandem Drive Clutches

C1PFC

[PCLC-0355FCZZ

] &

C1PTC

[PCLC-0354FCZZ]

when Tray 1 counter reaches 3000K

Replace Tandem Drive Clutch

C2PFC

[PCLC-0355FCZZ]

when

Tray 2 counter reaches 3000K

Replace Multi Stage Clutch

C3PFC

[PCLC-0356FCZZ]

when Tray 3

counter reaches 3000K

Replace Multi Stage Clutch

C4PFC

[PCLC-0356FCZZ]

when Tray 4

counter reaches 3000K

Summary of Contents for MX-M1054













































































Search results

Summary of Contents for MX-M1054

Reviews:

Sharp MX-M1054, Technical Handy Manual, Page: 18 / 76

Search results

Summary of Contents for MX-M1054

Reviews: