manualshive.com logo in svg

Sharp MX-M1054, Technical Handy Manual, Page: 30 / 76

Share
Download
Sharp MX-M1054 Technical Handy Manual Download Page 30

Firmware Recovery 

 

 

30 

SHARP

 

Document Solution Centre

  

 

 

6.

 

Using the [UP] and [DOWN] keys, navigate and select  
the required firmware SFU file . 

 

 

 

Use the [OK] key to browse through to the sub folder(s) or  

 

 

[BACK] key to return to the parent folder(s). 

 
 

7.

 

Press [OK]. – It will take approx. 1-2 minutes to read the  

 

SFU file. 

 
 

8.

 

After reading is completed, the firmware update (writing)  

 

will commence. 

 
 

 

Note:   

 

 

The abbreviated name/location of the firmware that is being 

 

 

updated will appear in the upper right corner. 

 

9.

 

If the firmware upgrade completes successfully,  

 

RESULT OK will be displayed. 

 

10.

 

Power off the MFP. Pull out the MFP PWB and 
Turn OFF MFP PWB UPDATE DIP SW. 

 

11.

 

Insert and secure the MFP PWB and refit the Right Rear  
Cabinet. 

 

 

Firm Update 
> 0100h200.sfu

 

Firm Update 
    Reading Data

 

Firm Update           IcuM 
    Writing Data

 

Firm Update           IcuM 
    Result  :  OK

 

Summary of Contents for MX-M1054













































































Reviews:

No comments