manualshive.com logo in svg

Sharp LH79524, User Manual

The Sharp LH79524 User Manual is a comprehensive guide designed to assist users in navigating and optimizing their LH79524 device. Packed with essential instructions and insights, this manual can be easily downloaded for free from our website, ensuring a hassle-free access to enriching product knowledge and functionalities.

Share
Download
background image

Table of Contents

LH79524/LH79252 User’s Guide

iv

Version 1.0

4.5.3.3 Clock and Signal Polarity Control Register (TIMING2)..................... 4-24
4.5.3.4 Upper Panel Frame Buffer Base Address Register (UPBASE)........ 4-26
4.5.3.5 Lower Panel Frame Buffer Base Address Register (LPBASE) ........ 4-27
4.5.3.6 Interrupt Enable Register (INTREN)................................................. 4-28
4.5.3.7 CLCDC Control Register (CTRL) ..................................................... 4-29
4.5.3.8 Raw Interrupt Status Register (STATUS)......................................... 4-32
4.5.3.9 Masked Interrupt Status Register (INTERRUPT) ............................. 4-33
4.5.3.10 Interrupt Clear Register (INTCLR).................................................. 4-34
4.5.3.11 LCD Upper Panel and Lower Panel Frame Buffer Current 

Address Register (UPCURR and LPCURR) ............................................ 4-35

4.5.3.12 256 × 16-bit Color Palette Register (PALETTE) ............................. 4-36

4.5.4 ALI Register Reference ........................................................................... 4-38
4.5.5 ALI Memory Map ..................................................................................... 4-38
4.5.6 ALI Register Descriptions ........................................................................ 4-38

4.5.6.1 Setup Register (ALISETUP) ............................................................. 4-38
4.5.6.2 Control Register (ALICTRL) ............................................................. 4-39
4.5.6.3 Timing Delay Register 1 (ALITIMING1)............................................ 4-40
4.5.6.4 Timing Delay Register 2 (ALITIMING2)............................................ 4-41

4.6 Timing Waveforms ......................................................................................... 4-42

4.6.1 STN Horizontal Timing ............................................................................ 4-42
4.6.2 STN Vertical Timing ................................................................................ 4-42
4.6.3 TFT Horizontal Timing ............................................................................. 4-42
4.6.4 TFT Vertical Timing ................................................................................. 4-42
4.6.5 AD-TFT/HR-TFT Horizontal Timing Waveforms...................................... 4-42
4.6.6 AD-TFT/HR-TFT Vertical Timing Waveforms.......................................... 4-42

Chapter 5 – Direct Memory Access Controller

5.1 Theory Of Operation......................................................................................... 5-2

5.1.1 Use for SSP and UART ............................................................................. 5-3
5.1.2 Changing Mode from Memory to Peripheral ............................................. 5-3
5.1.3 Interrupt, Error, and Status Registers........................................................ 5-4

5.1.3.1 Interrupts ............................................................................................ 5-4

5.1.4 External DMA Handshake Signal Timing .................................................. 5-4

5.2 Register Reference .......................................................................................... 5-5

5.2.1 Memory Map ............................................................................................. 5-5
5.2.2 Register Definitions ................................................................................... 5-6

5.2.2.1 Source Base Registers (SOURCELO and SOURCEHI) .................... 5-6
5.2.2.2 Destination Base Registers (DESTLO and DESTHI) ......................... 5-7
5.2.2.3 Maximum Count Register (MAX)........................................................ 5-8
5.2.2.4 Control Register (CTRL)..................................................................... 5-9
5.2.2.5 Current Source Registers (CURSHI and CURSLO)......................... 5-12
5.2.2.6 Current Destination Registers (CURDHI and CURDLO).................. 5-13
5.2.2.7 Terminal Count Register (TCNT)...................................................... 5-14
5.2.2.8 Interrupt Mask Register (MASK)....................................................... 5-15
5.2.2.9 Interrupt Clear Register (CLR).......................................................... 5-16
5.2.2.10 Status Register (STATUS) ............................................................. 5-17

Summary of Contents for LH79524












































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for LH79524

UE 120 Series Installation And Maintenance Instructions preview
120 Series
Brand: UE Pages: 4
XBOX 360 Manual preview
360
Brand: XBOX Pages: 7
Campbell CR10 PROM Replacement Procedure preview
CR10 PROM
Brand: Campbell Pages: 8
Campbell CS225 Instruction Manual preview
CS225
Brand: Campbell Pages: 22
Danfoss vlt soft starter mcd 500 Operating Instruction preview
vlt soft starter mcd 500
Brand: Danfoss Pages: 95
Danfoss EKE 347 Installation Manual preview
EKE 347
Brand: Danfoss Pages: 12
Danfoss VLT 5000 Instruction Manual preview
VLT 5000
Brand: Danfoss Pages: 33
Danfoss VLT 6000 Installation Manual preview
VLT 6000
Brand: Danfoss Pages: 59
Danfoss EKC 361 User Manual preview
EKC 361
Brand: Danfoss Pages: 16
Danfoss VLT AQUA Drive FC 200 Operating Instructions Manual preview
VLT AQUA Drive FC 200
Brand: Danfoss Pages: 91
Danfoss EvoFlat WSS Installation Manual preview
EvoFlat WSS
Brand: Danfoss Pages: 2
Danfoss FC 300 Operating Instructions Manual preview
FC 300
Brand: Danfoss Pages: 100
Danfoss FC 300 Operating Instruction preview
FC 300
Brand: Danfoss Pages: 82
Danfoss Optyma Plus User Manual preview
Optyma Plus
Brand: Danfoss Pages: 18
Danfoss AMV 438 SU Installation Manual preview
AMV 438 SU
Brand: Danfoss Pages: 12
Danfoss OPTYMA Plus OP-LPQM Manual preview
OPTYMA Plus OP-LPQM
Brand: Danfoss Pages: 8
Easy-Laser E540 Manual preview
E540
Brand: Easy-Laser Pages: 84
Easy Heat RS2 Installation And Operation Instructions preview
RS2
Brand: Easy Heat Pages: 4

Brands by name

Popular brands

Load more brands