Sharp LH79524 User Manual Download Page 50 | Manualshive

Page: 50 / 555

background image

LH79524/LH79525 User’s Guide

Overview

Version 1.0

1-7

1.3.1.2 Synchronous and Asynchronous Bus Clocking Modes

Although the frequency of FCLK must always be greater than (or equal to) HCLK, the two
Standard modes vary the relationship between these two clock signals. In the Synchro-
nous Mode, the FCLK frequency must be programmed to be an even integer multiple of
the HCLK frequency. Bus accesses in the Synchronous Mode require a re-synchronization
delay of at least one wait state. In the Asynchronous Mode the harmonic relationship
between the clocks need not be maintained; the two clock signals may be of unrelated fre-
quency. Bus accesses in the Asynchronous Mode require a minimum re-synchronization
delay of two wait states.

1.3.1.3 Fastbus Extension Bus Clocking Mode

Designs involving frequent accesses of high-speed memory may benefit by using the
Fastbus Extension Mode. This inherently synchronous mode clocks the core, cache, and
AHB at the same frequency. Where the Standard modes utilized two different clocks, the
Fastbus mode operates the core, cache, and AHB interface with two signals derived from
the same source; essentially the same clock. Figure 1-3 shows the Fastbus Extension
Mode clocking arrangement. The Fastbus Extension Mode does not require re-synchroni-
zation delays.

The Fastbus Extension Mode is useful for applications involving frequent AHB accesses.
Although the core’s frequency is limited by the AHB maximum frequency, the Fastbus
Extension Mode avoids the wait-state penalties imposed by the Standard modes.

Figure 1-3. Fastbus Clocking Mode

CORE

LH79525-50

CACHE

HCLK_CPU

HCLK

COMMON CLOCK

SOURCE

NOTE: This is a conceptual drawing

AHB

INTERFACE

ARM720T

ADVANCED

HIGH-PERFORMANCE

BUS (AHB)

«
...
48
49
50
51
52
...
»

Summary of Contents for LH79524












































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for LH79524

Brand: Sole Diesel Pages: 8

Brand: IBM Pages: 105

Brand: Panasonic Pages: 72

Brand: Panasonic Pages: 45

Brand: Panasonic Pages: 24

Brand: E+E Elektronik Pages: 20

ServeRAID-MR10is

Brand: IBM Pages: 94

ServeRAID-4 Ultra160 Series

Brand: IBM Pages: 20

8271 Nways Ethernet LAN Switch

Brand: IBM Pages: 6

Brand: IBM Pages: 86

Brand: IBM Pages: 205

Brand: IBM Pages: 28

Brand: ZPA Pecky, a.s. Pages: 36

Brand: Dakota Digital Pages: 12

Brand: I-Tork Pages: 15

Brand: MGC Pages: 16

Brand: Seiko Pages: 30

ASC G Wi-Fi kit

Brand: Waeco Pages: 386

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands