manualshive.com logo in svg

Sharp LH79524, User Manual

The Sharp LH79524 User Manual is a comprehensive guide designed to assist users in navigating and optimizing their LH79524 device. Packed with essential instructions and insights, this manual can be easily downloaded for free from our website, ensuring a hassle-free access to enriching product knowledge and functionalities.

Share
Download
background image

LH79524/LH79525 User’s Guide

Ethernet MAC Controller

Version 1.0

 6-47

6.3.3.19 SQE Test Errors (SQERR)

This 8-bit register contains the number of frames where the ETHERCOL pin was not 
asserted within 96 bit times (one inter-frame gap) of the ETHERTXEN pin being deas-
serted in half-duplex mode. 

6.3.3.20 Received Length Field Mismatch (RXLEN)

This register counts the number of received frames that have a measured length shorter 
than specified in its length field. Checking is enabled via the NETCONFIG:LENGTHCHK 
bit. Frames containing a type ID in bytes 13 and 14 (length/type ID 

≥

 0x0600) will not be 

counted as length field errors, nor will excessive length frames.

Table 6-70. SQERR Register

BIT

31

30

29

28

27

26

25

24

23

22

21

20

19

18

17

16

FIELD

///

RESET

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

TYPE

RO

RO

RO

RO

RO

RO

RO

RO

RO

RO

RO

RO

RO

RO

RO

RO

BIT

15

14

13

12

11

10

9

8

7

6

5

4

3

2

1

0

FIELD

///

SQERR

RESET

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

TYPE

RO

RO

RO

RO

RO

RO

RO

RO

RW

RW

RW

RW

RW

RW

RW

RW

ADDR

0xFF 0x84

Table 6-71. SQERR Fields

BITS

NAME

FUNCTION

31:8

///

Reserved

Reading returns 0. Write the reset value.

7:0

SQERR

SQE Test Errors

Shows the number of frames where the ETHERCOL pin was 

not asserted within 96 bit times

Table 6-72. RXLEN Register

BIT

31

30

29

28

27

26

25

24

23

22

21

20

19

18

17

16

FIELD

///

RESET

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

TYPE

RO

RO

RO

RO

RO

RO

RO

RO

RO

RO

RO

RO

RO

RO

RO

RO

BIT

15

14

13

12

11

10

9

8

7

6

5

4

3

2

1

0

FIELD

///

RXLEN

RESET

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

TYPE

RO

RO

RO

RO

RO

RO

RO

RO

RW

RW

RW

RW

RW

RW

RW

RW

ADDR

0xFF 0x88

Table 6-73. RXLEN Fields

BITS

NAME

FUNCTION

31:8

///

Reserved

Reading returns 0. Write the reset value.

7:0

RXLEN

Receive Length Field Mismatch

Contains the number of received frames that 

have a measured length shorter than that extracted from its length field. 

Summary of Contents for LH79524












































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for LH79524

Eaton CMA User Manual preview
CMA
Brand: Eaton Pages: 50
ECKELMANN VS 3010 BS Operating Instruction preview
VS 3010 BS
Brand: ECKELMANN Pages: 178
echoflex RTS Installation Manual preview
RTS
Brand: echoflex Pages: 8
H3C WX Series Registration And Activation Manual preview
WX Series
Brand: H3C Pages: 17
H3C WX Series Getting Started Manual preview
WX Series
Brand: H3C Pages: 32
H3C S9500E Series Card Manual preview
S9500E Series
Brand: H3C Pages: 5
H3C WX1800H series Command Reference Manual preview
WX1800H series
Brand: H3C Pages: 27
H3C WX3500H series Installations preview
WX3500H series
Brand: H3C Pages: 4
H3C WX5540H Installation Manual preview
WX5540H
Brand: H3C Pages: 54
H3C LSWM1WCM10 Manual preview
LSWM1WCM10
Brand: H3C Pages: 10
H3C LSQM1WCMB0 Quick Start Manual preview
LSQM1WCMB0
Brand: H3C Pages: 10
Hanwell MS1000 Installation Manual preview
MS1000
Brand: Hanwell Pages: 34
HANSONG BM240 User Manual preview
BM240
Brand: HANSONG Pages: 11
Datapath HX4 Quick Start Manual preview
HX4
Brand: Datapath Pages: 12
Hansen HS6 Specifications, Applications, Service Instructions & Parts preview
HS6
Brand: Hansen Pages: 4
Decagon GS3 Operator'S Manual preview
GS3
Brand: Decagon Pages: 27
Frico ERP Instruction Manual preview
ERP
Brand: Frico Pages: 12
Ebode XDOM TAKE 6 IR/RF - PRODUCTSHEET User Manual preview
XDOM TAKE 6 IR/RF - PRODUCTSHEET
Brand: Ebode Pages: 88

Brands by name

Popular brands

Load more brands