manualshive.com logo in svg

Sharp LH79524, User Manual

The Sharp LH79524 User Manual is a comprehensive guide designed to assist users in navigating and optimizing their LH79524 device. Packed with essential instructions and insights, this manual can be easily downloaded for free from our website, ensuring a hassle-free access to enriching product knowledge and functionalities.

Share
Download
background image

LH79524/LH79525 User’s Guide

Direct Memory Access Controller

Version 1.0

 5-13

5.2.2.6 Current Destination Registers (CURDHI and CURDLO)

The Current Destination Registers are 16-bit Read Only registers that hold the current 
value of the destination address pointer. The value in the registers is used as an AHB 
address in a DMA-to-destination data transfer over the AHB. If the DeInc bit in the Control 
Register is set to 1, the value in the Current Destination Registers increments as data 
transfers from the DMA to a destination. The value increments at the end of the address 
phase of the AHB transfer by the HSIZE value. If the DeInc bit is 0, the Current Destination 
Register holds the same value during the entire DMA data transfer. 

 

 

Table 5-23. CURDHI Register

BIT

31

30

29

28

27

26

25

24

23

22

21

20

19

18

17

16

FIELD

///

RESET

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

RW

RO

RO

RO

RO

RO

RO

RO

RO

RO

RO

RO

RO

RO

RO

RO

RO

BIT

15

14

13

12

11

10

9

8

7

6

5

4

3

2

1

0

FIELD

CURDHI

RESET

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

RW

RW

RW

RW

RW

RW

RW

RW

RW

RW

RW

RW

RW

RW

RW

RW

RW

ADDR

DATASTREAM x BASE + 0x020

Table 5-24. CURDHI Fields

BITS

NAME

DESCRIPTION

31:16

///

Reserved

Reading returns 0. Write the reset value.

15:0

CURDHI

Current Destination Upper Address

This field contains the upper 16-bits of 

the address for the destination of data for the current DMA transfer.

Table 5-25. CURDLO Register

BIT

31

30

29

28

27

26

25

24

23

22

21

20

19

18

17

16

FIELD

///

RESET

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

RW

RO

RO

RO

RO

RO

RO

RO

RO

RO

RO

RO

RO

RO

RO

RO

RO

BIT

15

14

13

12

11

10

9

8

7

6

5

4

3

2

1

0

FIELD

CURDLO

RESET

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

RW

RW

RW

RW

RW

RW

RW

RW

RW

RW

RW

RW

RW

RW

RW

RW

RW

ADDR

DATASTREAM x BASE + 0x024

Table 5-26. CURDLO Fields

BITS

NAME

DESCRIPTION

31:16

///

Reserved

Reading returns 0. Write the reset value.

15:0

CURDLO

Current Destination Lower Address

This field contains the lower 16-bits 

of the address for the destination of data for the current DMA transfer.

Summary of Contents for LH79524












































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for LH79524

Hankscraft Runxin HD Series Service Manual preview
HD Series
Brand: Hankscraft Runxin Pages: 53
Hach SC4200c User Manual preview
SC4200c
Brand: Hach Pages: 36
Hach 2100Q User Instructions preview
2100Q
Brand: Hach Pages: 72
Nedap WIM Installation Manual preview
WIM
Brand: Nedap Pages: 20
Sanhua DPF Series Instructions preview
DPF Series
Brand: Sanhua Pages: 3
QED MP50 Instruction Manual preview
MP50
Brand: QED Pages: 26
Zeta Premier MX-16 Installation And Commissioning Manual preview
Premier MX-16
Brand: Zeta Pages: 44
WURM Frigolink FVB110B Product Information preview
Frigolink FVB110B
Brand: WURM Pages: 4
Ban Seok BV-322M User Manual preview
BV-322M
Brand: Ban Seok Pages: 9
Taconova NOVASTAT EL DIGITAL Manual preview
NOVASTAT EL DIGITAL
Brand: Taconova Pages: 7
Insignia NS-GPS4RC101 Quick Setup Manual preview
NS-GPS4RC101
Brand: Insignia Pages: 2
Thermomart PID-4CH-SSR Instruction Manual preview
PID-4CH-SSR
Brand: Thermomart Pages: 6
ACL ACL 5500 Installation Manual preview
ACL 5500
Brand: ACL Pages: 20
asalvo TRIO ROMA Instruction Manual For Use preview
TRIO ROMA
Brand: asalvo Pages: 46
Megalarm MEGA 1100 Installation & Operation Manual preview
MEGA 1100
Brand: Megalarm Pages: 2
Kathrein ESO 125 Installation And Operation Manual preview
ESO 125
Brand: Kathrein Pages: 32
Rain Bird TBOS-BT Manual preview
TBOS-BT
Brand: Rain Bird Pages: 38
E+L RK 4004 Manual preview
RK 4004
Brand: E+L Pages: 62

Brands by name

Popular brands

Load more brands