66
04
●
The following signals are sent to the line and the main body speaker.
●
The send signals are as follows:
01: No signal is sent.
26: 7eH flag signal
27, 28, 30: Tone signal
31: Pseudo ringer sound (With the On-hook key pressed)
32: Voice message silent <Not used>
33: Ring back tone silent <Not used>
34: Dial pulse make
Under the state where dial pulses can be sent to the line, the make state is
kept.
35: Dial pulse break
Under the state where dial pulses can be sent to the line, the break state is
kept.
Other than the above: FFH
●
The signal send level is selectable between 0db or the soft SW set value.
Since, however this setup is not required for pseudo ringer sound, voice
message (silent), ring back tone (silent), and dial pulse make/break., the
selection menu does not appear. (For 01, 31 to 35, selection between 0db and
the soft SW set value cannot be made.)
●
Signal send is continued until an interruption command is outputted.
●
The signal send level is returned to the soft SW set value before execution of
this mode when this mode is terminated.
06
Confidential
communication
password print
Used to print the currently set confidential communication password.
07
Image memory content
output
Used to print all image data stored in the image memory. The following
image data are also outputted.
●
Image data received in a confidential communication remote send image data
read in the memory
Note: Image data are cleared after being outputted.
08
Voice message send
<Not used>
Used to send the voice reply message.
10
Image memory clear
Used to clear all data stored in the image memory.
The following data are also cleared.
• Image data received in confidential communication
• The management table is also initialized.
Display/Key operation
<Signal send level>
0db: Signals are
sent in 0db.
Soft SW: Signals
are sent in the
level set with the
soft SW.
<Send signals>
01: No signal (CMLON)
02: 33600bps (V34)
03: 31200bps (V34)
04: 28800bps (V34)
05: 26400bps (V34)
06: 24000bps (V34)
07: 21600bps (V34)
08: 19200bps (V34)
09: 16800bps (V34)
10: 14400bps (V34)
11: 12000bps (V34)
12: 9600bps (V34)
13: 7200bps (V34)
14: 4800bps (V34)
15: 2400bps (V33)
16: 14400bos (V33)
17: 12000bps (V33)
18: 14400bps (V17)
19: 12000bps (V17)
20: 9600bps (V17)
21: 7200bps (V17)
22: 9600bps (V29)
23: 7200bps (V29)
24: 4800bps (V27ter)
25: 2400bps (V27ter)
26: 300bps (FLAG)
27: 2100Hz (CED)
28: 1100Hz (CNG)
29: 300bps (V21)
30: 2100Hz (ANSam)
31: Pseudo ring sound
32: Voice message silent
33: Ring back tone silent
34: Dial pulse make
35: Dial pulse break
<Sound volume setup>
LARGE: Signals are sent
in the LARGE sound
volume level.
Soft SW: Signals are sent
in the level set with the
soft switch 70-1.
<Message>
1: “Wait for a moment.”
2: “No one is around the phone. For
FAX send, please press the START button.
(FAX/TEL reply message)
3: Reserved sound
DM-FX1
5 – 4
