Sharp AR-M351N, Service Manual

Page: 210 / 276

AR-M351U/M451U, AR-M355U/M455U SIMULATION 9 - 74
Operation/Procedure
1) Enter the number corresponding to the memory to be checked
with 10-key.
2) Press [START] key.
In the case of All, all memories are checked only once.
The error address or the data line is displayed individually.
When "repeat" is selected, the operation is repeated until the
result is "NG" or [CUSTOMSETTING" is pressed.
When Check is "once," the display stops at the result display.
When [CUSTOM SETTINGS] key is pressed, the display returns
to the initial display.
Operation/Procedure
1) Enter the number corresponding to the output mode with 10-
key.
2) Press [START] key.
The output is delivered at the max. send level.
When [CUSTOM SETTINGS] key is pressed during execution,
execution is stopped.
When a number is entered and [START] key is pressed during
execution, the kind of signal can be changed.
Press [START] key.
66-3
Purpose Operation test/Check
Function
(Purpose) Used to check the operation of the FAX PWB
memory (read/write). (This adjustment is required
when the PWB is replaced with a new one.) (Only
when FAX is installed)
Section FAX
Item Data
Check connection wire list
NO CHECK Not checked yet.
CHECKING Checking
OK Check complete OK
NG Check complete NG
Target memory of check
MFP SRAM
SRAM
MFP FLASH FLASH ROM
MFP OP.FLASH
MODEM EEPROM
MODEM SRAM (G/A)
MODEM SDRAM1
MODEM SDRAM2
SIMULATION 66-2
FAX SOFT SW. CLEAR(WITHOUT ADJUSTMENT VALUE).
INPUT COUNTRY CODE, AND PRESS START.
1 2 3 4 5 6 7 8
1
SIMULATION 66-2
FAX SOFT SW. CLEAR.
ARE YOU SURE?
JAPAN
1:YES
2:NO
Press [START] key. Press [CUSTOM SETTINGS] key.
66-4
Purpose Operation test/Check
Function
(Purpose) Used to check the output operation of data signals
in each data output mode of FAX. (Used to check
the operation of MODEM. ) Send level: Max. (Only
when FAX is installed)
Section FAX
Item Operation
1 NOSIGNAL No signal 17 12.0 V33 12.0 V33
2 33.6 V34 26.4 V34 18 14.4 V17 14.4 V17
3 31.2 V34 31.2 V34 19 12.0 V17 12.0 V17
4 28.8 V34 28.8 V34 20 9.6 V17 9.6 V17
5 26.4 V34 26.4 V34 21 7.2 V17 7.2 V17
6 24.0 V34 24.0 V34 22 9.6 V29 9.6 V29
7 21.6 V34 21.6 V34 23 7.2 V29 7.2 V29
8 19.2 V34 19.2 V34 24 4.8 V27t 4.8 V27t
9 16.8 V34 16.8 V34 25 2.4 V27t 2.4 V27t
10 14.4 V34 14.4 V34 26 0.3 FLG 0.3 FLG
11 12.0 V34 12.0 V34 27 CED 2100 CED 2100
12 9.6 V34 9.6 V34 28 CNG 1100 CNG 1100
13 7.2 V34 7.2 V34 29 0.3 V21 0.3 V21
14 4.8 V34 4.8 V34 30 ANSam ANSam
15 2.4 V34 2.4 V34 31 RINGER RINGER
16 14.4 V33 14.4 V33 32 No RBT No RBT
SIMULATION 66-3
FAX PWB MEMORY CHECK INPUT 1-13, AND PRESS START.
1. All Memory Device Check (once)
2. MFP SRAM(once) 3. MFP SRAM(repeat)
4. MFP FLASH+ OP.FLASH(once)
5. MFP FLASH+ OP.FLASH(repeat)
6. MODEM EEPROM(once) 7. MODEM EEPROM(repeat)
8. MODEM SRAM(G/A)(once) 9. MODEM SRAM(G/A)(repeat)
10. MODEM SDRAM1(once) 11. MODEM SDRAM1(repeat)
12. MODEM SDRAM2(once) 13. MODEM SDRAM2(repeat)
When "repeat" is selected and
[CUSTOM SETTINGS] key is pressed.
SIMULATION 66-3
FAX PWB MEMORY CHECK
MFP SRAM: CHECKING
MFP FLASH: NO CHECK
MFP OP.FLASH: NO CHECK
MODEM EEPROM: NG:A0010000
MODEM SRAM(G/A):NO CHECK
MODEM SDRAM1: NG A11
MODEM SDRAM2: OK