Sharp AR-M351N Service Manual Download Page 126

Page: 126 / 276

AR-M351U/M451U, AR-M355U/M455U ADJUSTMENTS 8 - 7

<Specification>

<3> SPF scan distortion adjustment

Items which must have been completed before this adjust-
ment.

• Adjustment on the engine side (If there is no problem in self

print, no need to adjust.)

• OC scan distortion adjustment

• SPF height adjustment

Items which must be executed after completion of this adjust-
ment.

• SPF off-center

• SPF lead edge adjustment

• Front/rear and left/right void amount setting

1) Make a test chart as shown below. (Print a self-print pattern

71.)

2) Make a copy with DSPF.

3) Check that it is in the specified range.

4) Execute SIM51-2 to check the SPF set value.

Change the set value of the SPF resist amount to the following
value.

5) Though the SPF resist amount is the above value, if there is

any distortion in SPF scan, adjust the SPF installing position in
the following procedures.

6) Loosen the nut which is fixing the adjustment set screw of the

hinge R, and adjust the adjustment set screw.

7) Make a copy again, and check again that the value is in the

specified range.

8) Tighten the nut to fix the adjustment screw.

<Specification>

∗

After the SPF distortion adjustment, perform SIM53-8 SPF
scanning position automatic adjustment.

<4> OC scan magnification ratio adjustment

Items which must have been completed before this adjust-
ment.

• Adjustment on the engine side (If there is no problem in self

print, no need to adjust.)

• OC scan distortion adjustment

Items which must be executed after completion of this adjust-
ment.

• OC scan lead edge adjustment

• Original off-center adjustment

1) Place a print of self-print pattern (A3 or WLT) 70 or a scale on

the table glass.

2) Close the original cover, and make a copy.

3) Check that the value is within the specification.

4) If the value is not within the specified range, execute SIM48-1

(item 3, 4).

5) Make a copy again and check again that the value is within the

specification.

Specification

Adjustment

position

Distance between
dove (Reference
plate) and table
glass

3-point contact
(Left front/Left rear/Right
front when viewed from
the front)

Hinge
adjustment set
screw

SPF (HIGH)

SPF (LOW)

Specification

Adjustment position

Skew feed

Within ±3mm

Hinge R adjustment screw

SIMULATION 51-2

RESIST TIMING ADJUSTMENT. SELECT 0-8, AND PRESS START.

0.TRAY SELECT

1.PRINT START

2.TRAY1

3.TRAY2

4.DESK

5.BPT

6.ADU

7.SPF(HIGH)

8.SPF(LOW)

Summary of Contents for AR-M351N





















































































































































































































































































Search results

Summary of Contents for AR-M351N

Reviews:

Related manuals for AR-M351N

Brands by name

Popular brands

Sharp AR-M351N, Service Manual

Search results

Summary of Contents for AR-M351N

Reviews:

Related manuals for AR-M351N

Brands by name

Popular brands