Sharp AR-M351N, Service Manual

Page: 145 / 276

AR-M351U/M451U, AR-M355U/M455U SIMULATION 9 - 9
(Built-in finisher)
(Console finisher)
( ) : Added when the punch unit is installed.
Operation/Procedure
1) Select the number corresponding to the target of operation
check with 10-key.
2) Press START key.
The load selected in procedure 1 is operated.
Press [CUSTOM SETTINGS] key to stop the operation of the
load.
Operation/Procedure
Enter the adjustment value with 10 digit key pad and press START
key. The jogger moves to LT position (Inch series) or A4 position
(AB series) according to the entered value, and stops there.
Operation/Procedure
1) Select the number corresponding to the target of operation
check with 10-key.
2) Press [START] key.
3) Enter the adjustment value with 10-key.
4) Press [START] key. (The entered value is stored.)
3-3
Purpose Operation test/Check
Function
(Purpose) Used to check the operation of the load in the
finisher and the control circuit.
Section Finisher
Item Operation
Built-in finisher
1 T2S Tray 2 solenoid
2 T2OM Paper exit motor
3 SPS Stopper solenoid
4 SCRS Roller pressure release solenoid
5 PPS Rear edge h folding solenoid
6 SCGS Compiler gate solenoid
7 STTM Staple rotation motor
8 STUM Stapler shift motor
9 MM Main drive motor
10 EVM Elevator motor
11 STM Staple motor
12 JRM Jogger motor rear
13 JFM Jogger motor front
14 PSM Pusher motor
Console finisher
1 FFC Folding clutch
2 FPSM Puncher side register motor
3 FPNM Punch motor
4 FLM Shift motor
5 FFSM Stapler motor
6 FSM Slide motor
7 FRJM Alignment motor R
8 FFJM Alignment motor F
9 FAM Bundle exit motor
10 FPM Paddle motor
11 FFM Transport motor
SIMULATION 3-3
FINISHER SENSOR CHECK.
PID SCID SCID2 PPD
SCPD POD T1PF T2UP
T2DN T2PD STSP STLS
STNC STHP JFHP JRHP
PSHP STUHP STTHP1
STTHP2 DOPD DSW1 DSW2
24VM MMLK
SIMULATION 3-2
FINISHER SENSOR CHECK.
FSSS FJS FFDSW FTCS FFDS
FSPS FSUC FSS FSTHPS FSHPS FLE FLLLS
FULS FFE FFES FFRHPS FFHPS FFPS FSLS
FBES FOBHPS FAS FRJHPS FFJHPS FARHPS FPHPS
FES
(FPE)(FPSHPS)(FPUC)(FPDS)(FPDSS4)(FPDSS3)(FPDSS2)
(FPDSS1)(FPTS)
Press [START] key, and the operation
is started. Press [CUSTOM SETTINGS] key, and
the operation is stopped.
3-6
Purpose Adjustment
Function
(Purpose) Used to adjust the stacking capacity of the
finisher. (Used to adjust the alignment plate
(jogger) stop position in the finisher paper width
direction. The adjustment is made by changing the
alignment plate home position in the paper width
direction by software.)
Section Finisher
Item Operation
Press [START] key, and the
operation is started. Press [CUSTOM SETTINGS] key, and the
operation is stopped.
Stops when the operation is terminated.
3-10
Purpose Adjustment
Function
(Purpose) Console finisher (AR-FN7) adjustment
Section Finisher
Item Operation
Item
Set
range
Initial
value
1STEP
1 Saddle binding position
adjustment 0 - 400 200 0.0707mm
2 Saddle folding position
adjustment 0 - 400 200 0.0525mm
3 Front alignment position
adjustment 0 - 20 10 0.367mm
4 Rear alignment position
adjustment 0 - 20 10 0.367mm
SIMULATION 3-3
FINISHER LOAD TEST. SELECT 1- AND PRESS START.
2
SIMULATION 3-3
FINISHER LOAD TEST. EXECUTING .
2
SIMULATION 3-6
FINISHER JOGGER ADJUSTMENT. INPUT VALUE 40-60, AND PRESS START.
50
SIMULATION 3-6
FINISHER JOGGER ADJUSTMENT. MOVING....
50