Sharp AR-M351N Service Manual Download Page 167

Page: 167 / 276

AR-M351U/M451U, AR-M355U/M455U SIMULATION 9 - 31

Operation/Procedure

1) Enter the tag number with 10-key.

2) Press [START] key.

Operation/Procedure

The operating conditions of sensors and detectors are displayed.

The active sensors and detectors are highlighted.

Operation/Procedure

The operating conditions of sensors and detectors are displayed.

The active sensors and detectors are highlighted.

Operation/Procedure

The operating conditions of sensors and detectors are displayed.

The active sensors and detectors are highlighted.

The paper width size detection level is displayed.

27-5

Purpose

Setting

Function
(Purpose)

Used to enter the machine tag No. (This function
allows to check the tag No. of the machine with the
host computer.)

Section

Communication unit (TEL/LIU/MODEM etc.)

Item

Specifications

Operation mode

30-1

Purpose

Operation test/Check

Function
(Purpose)

Used to check the operation of sensors and
detectors in other than the paper feed section and
the operations of the related circuits.

Item

Operation

PPD1

Resist roller front paper detection

POD1

After-fusing transport detection 1

POD2

After-fusing transport detection 2

POD3

Paper full detection

DSWL

Cabinet open detection

DSWF

Front door

30-2

Purpose

Operation test/Check

Function
(Purpose)

Used to check the operation of sensors and
detectors in the paper feed section and the related
circuits.

Section

Paper feed

Item

Operation

SIMULATION 27-5

TAG # SETTING. INPUT VALUE, AND PRESS START.

PRESENT: 00010000

NEW:

00009999

SIMULATION 30-1

SENSOR CHECK..
PPD1 POD1

POD2

POD3

DSWL

DSWF

CSS1

Tray 1 insertion detection

PED

Tray 1 paper empty detection

LUD

Tray 1 upper limit detection

MCSET

MP unit detection

MCDRS

MP unit side door open detection

MCPPD

MP tray transport detection

MCLUD

MP tray upper limit detection

MCPED

MP tray paper empty detection

MCSPD

MP tray remaining quantity detection

MCSS1

MP tray size detection 1

MCSS2

MP tray size detection 2

MCSS3

MP tray size detection 3

MCSS4

MP tray size detection 4

MP Tray size

(The detection size of MP tray is displayed.)

MPFSET

Manual feed tray detection

MPED

Manual feed tray paper empty detection

MPLD

Manual feed length detection

MPLS1

Manual feed pull-out sensor 1

MPLS2

Manual feed pull-out sensor 2

Bypass Tray size

(The detection size of manual feed tray is
displayed.)

40-1

Purpose

Operation test/Check

Function
(Purpose)

Used to check the operation of the manual feed
tray paper size detector and the related circuit.
(The operation of the manual feed tray paper size
detector can be monitored with the LCD display.)

Section

Paper feed

Item

Operation

MPLD

Manual tray length detection

MPLS1

Manual tray pull-out detection 1

MPLS2

Manual tray pull-out detection 2

BYPASS_WIDTH

Manual feed guide plate position

BYPASS_AD

Manual feed width detection volume
output AD value

Bypass Tray width
size

(Manual tray detection size is displayed.)
A4/A3, 11 x, B5/B4, 8.5 x , A4R, B5R,
A5R, 5.5x, 7.25x, EXTRA

SIMULATION 30-2

TRAY SENSOR CHECK..

CSS PED LUD

MCSET

MCDRS MCPPD MCLUD MCPED MCSPD MCSS1 MCSS2

MCSS3 MCSS4 (MP Tray size:

)

MPFSET

MPED MPLD MPLS1 MPLS2

(Bypass Tray size:

)

SIMULATION 40-1

BYPASS TRAY SENSOR CHECK..

MPLD

MPLS1 MPLS2

BYPASS_WIDTH:

2100

BYPASS_AD:

600

(Bypass Tray width size:

A4/A3

)

Summary of Contents for AR-M351N





















































































































































































































































































Search results

Summary of Contents for AR-M351N

Reviews:

Related manuals for AR-M351N

Brands by name

Popular brands

Sharp AR-M351N, Service Manual

Search results

Summary of Contents for AR-M351N

Reviews:

Related manuals for AR-M351N

Brands by name

Popular brands