Sharp AR-M351N, Service Manual

Page: 146 / 276

AR-M351U/M451U, AR-M355U/M455U SIMULATION 9 - 10
Operation/Procedure
The operating conditions of the sensors and detectors are dis-
played.
The active sensors and detectors are highlighted.
Operation/Procedure
1) Select the number corresponding to the target of operation
check with 10-key.
2) Press [START] key.
The load selected in procedure 1 is operated.
Press [CUSTOM SETTINGS] key to stop the operation of the load.
Operation/Procedure
The operating conditions of the sensors and detectors are dis-
played.
The active sensors and detectors are highlighted.
5 Staple rear one-position
binding position adjustment 0 - 200 100 0.04374mm
6 Staple front one-position
binding position adjustment 0 - 200 100 0.04374mm
7 Staple 2-position binding
center adjustment 0 - 200 100 0.04374mm
8 Staple 2-position binding pitch
adjustment 0 - 99 50 0.04374mm
9 Punch center adjustment
(Slide direction) 47 - 53 50 1mm
10 Punch hole position
adjustment (Paper feed
direction)
0 - 99 50 0.105mm
Press [START] key, and the operation
is started. Press [CUSTOM SETTINGS] key, and
the operation is stopped.
3-20
Purpose Operation test/Check
Function
(Purpose) Used to check the mail bin stacker sensor.
Section Mail bin stacker
Item Operation
MPFD1 Tray 1 paper full detection
MPFD2 Tray 2 paper full detection
MPFD3 Tray 3 paper full detection
MPFD4 Tray 4 paper full detection
MPFD5 Tray 5 paper full detection
MPFD6 Tray 6 paper full detection
MPFD7 Tray 7 paper full detection
MPFD8 Tray 8 paper full detection
MPID Interface unit paper entry detection
MPPD1 Paper transport sensor 1
MPPD2 Paper transport sensor 2
MPPD3 Paper transport sensor 3
MPPD4 Paper transport sensor 4
MPPD5 Paper transport sensor 5
M24VM 24V power supply
MDD1 Jam cancel door
MDOPD Interface unit door
Item
Set
range
Initial
value
1STEP
SIMULATION 3-10
CONSOLE FINISHER SETTING. SELECT 1-10,AND PRESS START.
1.SADDLE POSITION 2.FOLDING POSITION
3.FRONT ADJUST
4.REAR ADJUST 5.STAPLE REAR
6.STAPLE FRONT 7.STAPLE BOTH
8.STAPLE PITCH 9.PUNCH CENTER
10.PUNCH HOLE
1
SIMULATION 3-10
CONSOLE FINISHER SETTING. INPUT VALUE, AND PRESS START.
1.FOLDING POSITION
200
SIMULATION 3-20
MAIL BOX SENSOR CHECK.
MPFD1 MPFD2 MPFD3 MPFD4 MPFD5 MPFD6 MPFD7
MPFD8 MPID MPPD1 MPPD2 MPPD3 MPPD4 MPPD5
M24VM MDD1 MDOPD
3-21
Purpose Operation test/Check
Function
(Purpose) Used to check the operations of the mail bin
stacker loads.
Section Mail bin stacker
Item Operation
1 MM Main motor
2 GSOL1 Gate solenoid 1
3 GSOL2 Gate solenoid 2
4 GSOL3 Gate solenoid 3
5 GSOL4 Gate solenoid 4
6 GSOL5 Gate solenoid 5
7 GSOL6 Gate solenoid 6
8 GSOL7 Gate solenoid 7
Press [START] key, and the operation
is started. Press [CUSTOM SETTINGS] key, and
the operation is stopped.
4
4-2
Purpose Operation test/Check
Function
(Purpose) Used to check the operations of the sensors and
detectors in the paper feed section (desk paper
feed/large capacity tray) and the related circuit.
Section Paper feed
Item Operation
SIMULATION 3-21
MAIL BOX LOAD TEST. SELECT 1-8 AND PRESS START.
1.MM
2.GSOL1
3.GSOL2
4.GSOL3
5.GSOL4
6.GSOL5
7.GSOL6
8.GSOL7
2
SIMULATION 3-21
MAIL BOX LOAD TEST. EXECUTING....
1.MM
2.GSOL1
3.GSOL2
4.GSOL3
5.GSOL4
6.GSOL5
7.GSOL6
8.GSOL7
2