Sharp AR-M351N, Service Manual

Page: 220 / 276

AR-M351U/M451U, AR-M355U/M455U SIMULATION 9 - 84
Operation/Procedure
1) Enter the number corresponding to the check mode with 10-
key.
2) Press [START] key.
When check is completed normally, "OK" is displayed. Incase of
an error, "NG" is displayed.
When check is "repeat," the operation is continued until the result
is NG or [CUSTOM SETTINGS] key is pressed.
Operation/Procedure
1) Enter the number corresponding to the destination.
2) Press [START] key.
Operation/Procedure
1) The confirmation window is displayed. Select whether rewrit-
ing of the program into PIC installed in the FAX VOX is per-
formed or not.
NOTE: Release the write protect notch.
FAX program writing enabled (Jumpers and DIP SW
depending on the model.)
2) Press [START] key.
When reload is completed normally, "OK" is displayed. In case of
an error, "NG" is displayed.
NG cause:
• Write protect is set.
• PIC is not installed.
• Access error to PIC
Press [START] key.
After completion of reloading
66-36
Purpose Operation test/Check
Function
(Purpose) Used to check interface between MFPC controller
and MDMC. (Check of the data line or the
command line) (Only when FAX is installed)
Section FAX
Item Operation
1 MFPC
←
MDMC Date line once only
2 MFPC
→
MDMC Date line once only
3 MFPC
←
MDMC Data line repeat
4 MFPC
→
MDMC Data line repeat
5 MFPC
←
MDMC Command line once only
6 MFPC
→
MDMC Command line once only
7 MFPC
←
MDMC Command line repeat
8 MFPC
→
MDMC Command line repeat
SIMULATION 66-35
MODEM PROGRAM RELOAD.
ARE YOU SURE?
1. YES
2. NO
1
SIMULATION 66-35
MODEM PROGRAM RELOAD. EXECITOMG···
LOADER··· xxxxx
MODEM···· xxxxx
SIMULATION 66-35
MODEM PROGRAM RELOAD.
LOADER···OK
MODEM····COMPLETE
SIMULATION 66-36
MFPC-MDMC I/F CHECK. INPUT 1-8, AND PRESS START.
1. MFPC<-MDMC(DATA once)
2. MFPC->MDMC(DATA once)
3. MFPC<-MDMC(DATA repeat)
4. MFPC->MDMC(DATA repeat)
5. MFPC<-MDMC(CMD once)
6. MFPC->MDMC(CMD once)
7. MDPC<-MDMC(CMD repeat)
8. MFPC->MDMC(CMD repeat)
1
SIMULATION 66-36
MFPC-MDMC I/F CHECK. INPUT 1-8, AND PRESS START.
EXECUTING...(OK or NG)
SIMULATION 66-36
MFPC-MDMC I/F CHECK. INPUT 1-8, AND PRESS START.
EXECUTING...
Press [START] key.
When check is "once" or
"repeat" and the result is "NG": When check is "repeat" and
[CUSTOM SETTINGS] key ON:
66-39
Purpose Setting
Function
(Purpose) Used to set the destination specifications. (Only
when FAX is installed)
Section FAX
Item Specifications Operation
66-42
Purpose Setting
Function
(Purpose) PIC program rewriting (Only when FAX is
installed)
Section FAX
Item Operation
1 YES Execution
2 NO Cancel
Press [START] key.
SIMULATION 66-39
FAX DESTINATION SETUP.
SELECT 1-6, AND PRESS START
0. NO DESTINATION
1. JAPAN
2. U.S.A./CANADA
3. EUROPE
4. AUSTRALIA
5. CHINA
6. ASIA
1
SIMULATION 66-42
PIC PROGRAM RELOAD.
ARE YOU SURE ?
1.YES
2.NO
1
Press [START] key.
Press [START] key.
SIMULATION 66-42
PIC PROGRAM RELOAD EXECUTING ....
Press [CUSTOM SETTINGS] key.
SIMULATION 66-42
PIC PROGRAM RELOAD
OK