Sharp AL-1611 Operation Manual Download Page 73

Page: 73 / 80

MATERIAL SAFETY DATA SHEET

Date Revised: Jun.28. 2002
Date Issued: Oct.18.2001
MSDS NO. F-30841

4. FIRST-AID MEASURES

Route(s) of Entry :

Inhalation?

Skin?

Ingestion?

Possible but very unusual.

Inhalation

Remove to fresh air. If symptoms occur, consult medical personnel.

Skin Contact :

Wash with soap and water for 15 minutes or until particle is removed.
If irritation does occur, consult medical personnel.

Eye Contact

Flush eyes immediately with water for 15 minutes. If irritation does occur, consult medical
personnel.

Ingestion

Rinse with water and drink several glasses of water. If irritation or discomfort does occur,
consult medical personnel.

5. FIRE -FIGHTING MEASURES

Extinguishing Media :

water, CO

, foam and dry chemicals

Special Fire fighting Procedures :

None

Fire and Explosion Hazards :

Like most finely divided organic powders, it may form an explosive
mixture.

6. ACCIDENTAL RELEASE MEASURES

Personal Precautions

None

Environmental Precautions :

None

Methods for Cleaning Up :

Wipe off with paper or cloth. DO not use vacuum cleaner when a large
amount is released. It, like most finely divided organic powders, is capable
of creating a dust explosion.

7. HANDLING AND STORAGE

Handling

Technical Measures

: None

Precautions

: None

Safe Handling Advice : Use of a dust mask is recommended when handling a large quantity of toner or

during long term exposure, as with any non-toxic dust. Try not to disperse the
particles.

Storage

Technical Measures

: None

Storage Conditions

: Keep container closed and Store in a cool and dry place.

Keep out of the reach of children.

Incompatible Products : None

8. EXPOSURE CONTROL/PERSONAL PROTECTION

Engineering Measures

Ventilation

: None required with intended use.

Exposure limit values

OSHA-PEL (USA)

: 15m

/m³ (Total Dust) , 5m

/m³ (Respirable Dust)

ACGIH-TLV (USA)

: 10m

/m³ (Total Dust) , 3m

/m³ (Respirable Dust)

Personal Protective Equipment

Respiratory Protection : None required when used as intended in Sharp equipment.
Hand Protection

: None required when used as intended in Sharp equipment.

Eye Protection

: None required when used as intended in Sharp equipment.

Skin Protection

: None required when used as intended in Sharp equipment.

Other Protective equipment : Use of a dust mask and goggles are recommended when handling a

large quantity of toner or during long term exposure, as with any non-
toxic dust.

Page: 2/4

Summary of Contents for AL-1611

















































































Search results

Summary of Contents for AL-1611

Reviews:

Related manuals for AL-1611

Brands by name

Popular brands

Sharp AL-1611, Operation Manual

Search results

Summary of Contents for AL-1611

Reviews:

Related manuals for AL-1611

Brands by name

Popular brands