Sharp AL-1611 Operation Manual Download

Page: 72 / 80

MATERIAL SAFETY DATA SHEET

Date Revised: Jun.28. 2002
Date Issued: Oct.18.2001
MSDS NO. F-30841

1. PRODUCT AND COMPANY IDENTIFICATION

Product Name

AR-200TD/TD-J/TD-C/DC/MD/MD-J/CD/CD-C/LD/AL-160TD/AL-161TD
DM-200TD/TD-B (Black Developer)

Supplier Identification :

Sharp Corporation
22-22 Nagaike-cho, Abeno-ku, Osaka, Japan

Local suppliers are listed below. Please contact the nearest supplier for additional information.

Area

(Country)

(Name and Telephone Number)

U.S.A.

Sharp Electronics Corporation

Sharp Plaza, Mahwah, NJ
Telephone number for information

: 1-800-237-4277

Emergency telephone number

: 1-800-255-3924

Canada

Sharp Electronics of Canada Ltd.

Telephone number for information

: 905-890-2100

Emergency telephone number

: 1-800-255-3924

Australia

Sharp Corporation of Australia PTY. Ltd.

No1 Huntingwood Drive Huntingwood Blacktown N.S.W.
Telephone number for information

: 1300-13-50-22

Germany

Sharp Electronics (Europe) GMBH

Sonninstrasse 3, 20097 Hamburg
Telephone number for information

: 040-2376-2613

United

Sharp Electronics (U.K.) Ltd.

Kingdom

Telephone number for information

: 08705-274-277

France

Sharp Electronics (France) S.A.

Telephone number for information

: 01-49-90-34-00

Austria

Sharp Electronics GMBH

Telephone number for information

: 01-727-19-0

Italy

Sharp Electronics (Italia) S.P.A.

Telephone number for information

: 02895951

Spain

Sharp Electronics Espana S.A.

Telephone number for information

: 93-581-97-00

Netherlands

Sharp Electronics Benelux B.V.

Telephone number for information

: 30-6359500

Sweden

Sharp Electronics (Nordic) AB

Telephone number for information

: 08-634-36-00

2. COMPOSITION/INFORMATION ON INGREDIENTS

Substance[ ]

Preparation[X]

Ingredient

CAS No.

Proportion OSHA PEL

ACGIH TLV

MAK-TWA NOHSC- TWA

Iron powder

7439-89-6

>92.5%

Not listed

Styrene-Acrylate

29497-14-1

< 7%

Not listed

copolymer
Carbon black

1333-86-4

< 1%

3.5m

/m³

3.5m

/m³

Not listed

/m³

3. HAZARDS IDENTIFICATION

This Preparation is not classified as dangerous according to Directive 1999/45/EC
Most Important Hazards and Effects of the Products
Human Health Effects : There are no anticipated carcinogenic effects from exposure based on animal

tests performed using toner. When used as intended according to instructions,
studies do not indicate any symptoms of fibrosis will occur.

Environmental Effects

: No data are available.

Specific hazards

: None

North

America

Oceania

Europe

Page: 1/4

Summary of Contents for AL-1611

















































































Search results

Summary of Contents for AL-1611

Reviews:

Related manuals for AL-1611

Brands by name

Popular brands

Sharp AL-1611, Operation Manual

Search results

Summary of Contents for AL-1611

Reviews:

Related manuals for AL-1611

Brands by name

Popular brands