Sharp AL-1043 Service Manual Download Page 32

Page: 32 / 126

AL-1551 OPERATIONAL DESCRIPTIONS 7-5

5. Paper feed section and paper transport

section

A. Paper transport path and general operations

Paper feed is made in two ways; the tray paper feed and the manual
paper feed. The tray is of universal-type, and has the capacity of 250

sheets.

The front loading system allows you to install or remove the tray from the
front cabinet.

The general descriptions on the tray paper feed and the manual paper

feed operation are given below.

(1) Cassette paper feed operation

1) The figure below shows the positions of the pick-up roller, the paper

feed clutch sleeve, and the paper feed latch in the initial state without

pressing the COPY button after lighting the ready lamp.
The paper feed latch is in contact with the projection of the clutch

sleeve.

2) When the COPY button is pressed, the main drive motor starts

rotating to drive each drive gear.

The pick-up drive gear also is driven at that time. Since, however, the

paper feed latch is in contact with the projection of the clutch sleeve,
rotation of the drive gear is not transmitted to the pick-up roller, which

does not rotate therefore.

3) After about 0.1 sec from when the main motor start rotating, the tray

paper feed solenoid (PFS) turns on for a moment.

This disengages the paper feed latch from the projection of the
clutch sleeve, transmitting rotation of the pick-up drive gear to the

paper feed roller shaft, rotating the pick-up roller to feed the paper.

4) After more than half rotation of the pick-up roller, the paper feed latch

is brought in contact with a notch on the clutch sleeve, stopping

rotation of the pick-up roller.

(1)

Scanner unit

(9)

Drum

(2)

Copy lamp

(10)

Transfer unit

(3)

Lens unit

(11)

Pickup roller

(4)

LSU (Laser unit)

(12)

Manual paper feed tray

(5)

Paper exit roller

(13)

Manual paper feed roller

(6)

Main charger

(14)

PS roller unit

(7)

Heat roller

(15)

Paper feed roller

(8)

Pressure roller

(2)

(4)

(1)

(3)

(5)

(6)

(7)

(8)

(9)

(10)

(11)

(13)

(12)

(14)

(15)

OFF

PFS

OFF

RRS

OFF

PFS

OFF

RRS

+ "# $%&'

Summary of Contents for AL-1043































































































































Search results

Summary of Contents for AL-1043

Reviews:

Related manuals for AL-1043

Brands by name

Popular brands

Sharp AL-1043, Service Manual

Search results

Summary of Contents for AL-1043

Reviews:

Related manuals for AL-1043

Brands by name

Popular brands