Sharp AL-1043 Service Manual Download Page 75

Page: 75 / 126

AL-1551 SIMULATION, TROUBLE CODES 10-1

[10]SIMULATION, TROUBLE CODES

1. Entering the simulation mode

To enter the serviceman simulation mode, press the keys as follows:

Clear

→

Density select

→

Clear

→

Density select

To cancel the simulation mode, press the clear key.
Flow chart of entering the simulation mode

YES

Is there a sub
code ?

Press the COPY
key.

Press the COPY key.

The COPY QUANTITY
display blinks to indicate
"00" and the machine
enters the ready
state for sub code input.

Enter the sub code with
the COPY QUANTITY key.

10th digit

1st digit:

Press the COPY key.

The current set adjustment
value and the counter
value are displayed on the
COPY QUANTITY

displayed Sensor check,
etc. are displayed by the

alarm lamps, etc.

To change the current set
values, enter with the COPY
QUANTITY key.

10th digit:

1st digit:

Count up of values:
COPY QUANTITY key

Count down of values:
Zoom key + COPY
QUANTITY key

The entered value
is displayed on the
COPY QUANTITY
display.

Press the COPY
key.

The entered value
is registered.

Is it the

Preform the operation
according to the
simulation number.

performed ?

Press the clear key.

All displays on the
operation panel go off,
and the machine enters
the ready state for
entering the main code.

Press the clear key.

End

Is the
main code the
same ?

Is the
sub code
displayed ?

Press the clear key.

The COPY QUANTITY
display blinks to indicate
the previously set sub
enters the ready7 state for
sub code input.

code, and the machine

Press the clear key.

Enter the new main
code.

The main code is
displayed on the
COPY QUANTITY
display.

Start

Press the clear key.

Press the exposure
mode selector key.

All displays on the
operation panel go off,
and the machine enters

he ready state for entering
he main code.

Count up of values:
COPY QUANTITY key
Count down of values:
Zoom key + COPY
QUANTITY key

The main code is
displayed on the
COPY QUANTITY
display.

simulation for

operation

check?

Is another

simulation to be

Enter the main code with
the COPY QUANTITY key.

10th digit:

1st digit:

Count up of values:
COPY QUANTITY key
Count down of values:
Zoom key + COPY
QUANTITY key

Press the clear key.

Press the exposure
mode selector key.

Within 1sec

!"#

Summary of Contents for AL-1043































































































































Search results

Summary of Contents for AL-1043

Reviews:

Related manuals for AL-1043

Brands by name

Popular brands

Sharp AL-1043, Service Manual

Search results

Summary of Contents for AL-1043

Reviews:

Related manuals for AL-1043

Brands by name

Popular brands