background image

5

Safety information

• 

Do not open the device; there are no user-serviceable parts inside.

• 

Ensure that power is cut off when wiring the device to the AC mains supply.

• 

Ensure that the device is electrically connected to earth (ground).

• 

Do not apply power if the device or mains cable is in any way damaged. 

• 

Do not immerse the fixture in water or liquid.

DANGER!  Risk of electric shock. Do not open the device.

• 

Install in a location that prevents accidental contact with the device.

• 

Install only in a well-ventilated space. 

• 

Install at least 0.3 m (12 in.) away from objects to be illuminated. 

• 

Install only in accordance with applicable building codes. 

• 

Ensure a minimum clearance of 0.3m (12 in.) around the cooling fans.

• 

Do not paint, cover, or modify the device, and do not filter or mask the light. 

• 

Keep all flammable materials well away from the device.

• 

Allow the device to cool for 15 minutes after operation before touching it.

 

CAUTION:

 Exterior surface temperature after 5 min. operation = 45 °C (113 °F). Steady state = 68 °C (154 °F).

WARNING!  Take measures to prevent burns and fire.

•  Do not look directly at the light source from close range. 
• 

Take precautions to prevent injury due to falls when working at height. 

• 

For Permanent Outdoor Installations (POI), ensure that the fixture is securely fastened to a load-bearing surface with suitable 

corrosion-resistant hardware.

• 

For temporary installations with clamps, ensure that the quarter-turn fasteners are turned fully and secured with a suitable 

safety cable.

• 

For elevated installations, secure the fixture with suitable safety cables and always comply with relevant load dimensioning, 

safety standards and requirements.

• 

The standard safety wire cable must be approved for a safe working load (SWL) of 10 times the weight of the fixture, and 
it must have a minimum gauge of 4 mm.

WARNING!  Take measures to prevent personal injury.

WARNING! 

Read the safety precautions in this section before installing, powering, or operating 

this product.

SGM luminaries are intended for professional use only. They are not suitable for household use. 

Les luminaires SGM sont impropre à l’usage domestique. Uniquement à usage professionnel.

Review the following safety precautions carefully before installing or operating the device.

Summary of Contents for G-4 RGBAM WASH





























Reviews: