manualshive.com logo in svg

SEW-Eurodrive MOVI-C UHX45A Series, Manual

Share
Download
SEW-Eurodrive MOVI-C UHX45A Series Manual Download Page 73

5

Startup with PROFINET IO

Controlling the stations in test run

Manual – MOVI-C

®

 CONTROLLER advanced with PROFINET IO Fieldbus Interface

73

10. Create a boot project. This way, the IEC Editor project is stored on the SD memory

card  of  the  MOVI‑C

®

  CONTROLLER  and  is  still  available  after  a  restart  of  the

MOVI‑C

®

 CONTROLLER.

22807393419

ð

Correct process data transfer between PLC and MOVI‑C

®

 CONTROLLER can now

be tested.

5.5

Controlling the stations in test run

During  successful  communication  between  PLC  and  the  MOVI‑C

®

  CONTROLLER,

process data words are transferred between the devices without faults.

5.5.1

Creating a watch table

Watch tables allow for monitoring and controlling the process data exchange.

Proceed as follows:

ü

You  loaded  the  MOVISUITE

®

  project  to  the  MOVI‑C

®

  CONTROLLER  via  the

IEC Editor.

1. Switch to the TIA Portal project.

24777730/EN – 01/2018

Summary of Contents for MOVI-C UHX45A Series





























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands