manualshive.com logo in svg

SEW-Eurodrive MOVI-C UHX45A Series, Manual

Share
Download
SEW-Eurodrive MOVI-C UHX45A Series Manual Download Page 45

4

Installation notes

Status LEDs

Manual – MOVI-C

®

 CONTROLLER advanced with PROFINET IO Fieldbus Interface

45

LED

Meaning

–

Is reserved.

4.5.5

Status LED "L5"

 In preparation

4.5.6

Status LED "L6"

 In preparation

4.5.7

"US1" status LED

Indicates  the  operating  state  of  the  fieldbus.  The  status  LED  "US1"  meets  and  ex-
pands  the  requirements  of  AIDA  (

A

utomation 

I

nitiative  of  German 

D

omestic 

A

uto-

mobile manufacturers).

Status

Possible cause

Measure

Green

The fieldbus electronics is run-
ning properly.

–

Green, flashing
Lights up: 0.5 s
Disabled: 3 s

The fieldbus electronics is in
energy-saving mode (standby
mode).

–

Orange, flashing
Lights up: 0.25 s
Disabled:

 

0.25 s

The fieldbus electronics is just
running up after a reset.

–

Red

Error in the hardware of the
device.

Switch the device off and back
on again.

If the fault occurs again, con-
tact SEW-EURODRIVE ser-
vice.

24777730/EN – 01/2018

Summary of Contents for MOVI-C UHX45A Series





























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands