SEW-Eurodrive MOVI-C UHX45A Series, Manual

Share

Page: 40 / 92

SEW-Eurodrive MOVI-C UHX45A Series Manual Download Page 40

4

Installation notes

Electrical installation

Manual – MOVI-C

®

CONTROLLER advanced with PROFINET IO Fieldbus Interface

40

The integrated Ethernet switch

The device is equipped with an integrated 2 port Ethernet switch for connecting the
fieldbus technology. The following network topologies are supported:

•

Tree topology

•

Star topology

•

Line topology

•

Ring topology

Auto-crossing

The two ports leading out of the Ethernet switch have auto-crossing functionality. You
can use both patch and crossover cables to connect to the next Ethernet node.

Auto-negotiation

The baud rate and duplex mode are negotiated by both Ethernet nodes when estab-
lishing the connection. For this purpose, both Ethernet ports of the Ethernet connec-
tion support an auto-negotiation functionality and work with a baud rate of either
100 Mbit or 10 Mbit in full duplex or half duplex mode.

24777730/EN – 01/2018

«
...
38
39
40
41
42
...
»

Summary of Contents for MOVI-C UHX45A Series





























































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands