manualshive.com logo in svg

SEW-Eurodrive INTERBUS UFI11A, Manual

Share
Download
SEW-Eurodrive INTERBUS UFI11A Manual Download Page 35

Manual – Fieldbus Interface INTERBUS UFI11A 

35

5

INTERBUS Interface

5.5

PCP interface

The UFI11A fieldbus interface offers a standardized interface for parameter setting
using the "Peripherals Communication Protocol" (PCP). This communications channel
gives you full access to the parameters of the UFI11A fieldbus interface and the drive
parameters of the inverters connected to the UFI11A.

Overview of basic 
structure

The PCP channel must be set to one, two or four words using the DIP switches on the
UFI11A to enable access to the parameter values of the UFI11A fieldbus interface or the
inverter. Changing the number of PCP words varies the access speed to parameter va-
lues via the PCP channel. The PCP interface is implemented using PCP version 3.0 in
the UFI11A.

PCP services

The UFI11A fieldbus interface supports the PCP services shown in Fig. 10. However,
only the following services are relevant for setting parameters: 

•

Establishing the connection (Initiate)

•

Reading of parameter values (Read)

•

Writing of parameter values (Write)

•

Cancelling the connection (Abort)

05389AXX

Fig. 24: PCP services supported by the UFI11A fieldbus interface

Summary of Contents for INTERBUS UFI11A





































































Reviews:

No comments

Brands by name

Popular brands

Load more brands