SEPTENTRIO mosaic Series Hardware Manual Download Page 47

Page: 47 / 57

Evaluation Kit: mosaic-go

Mosaic-go provides a 5V DC supply to both antenna connectors. In the dual-antenna
version, a circuit similar to the one in section 4.2.3.2 is used. The combined main and
auxiliary antenna power consumption must not exceed 150mA.

Note that RF_IN2 is only available on the dual-antenna mosaic-go.

8.1.4

TF Card

Socket for a micro SD Card. See section 4.6 for details.

8.1.5

6-pin Connector

Type: GH connector, 1.25mm pitch, 6 way. Mating connector housing: GHR-06V-S

Pin Name

Direction Level

Description

Comment

VCC

PWR

4.75V-5.5V Main power supply

GND

Ground

TXD1

Out

3V3_LVTTL Serial COM1 transmit line

Directly connects to TXD1 of internal mosaic, see 4.3

RXD1

3V3_LVTTL Serial COM1 receive line

Directly connects to RXD1 of internal mosaic, see 4.3

PPS

Out

3V3_LVTTL PPS output

PPSO from mosaic converted to 3.3V, see 4.9

EVENT

3V3_LVTTL Event timer input

Connects to EVENTA of mosaic through a 3V3 to 1V8
level translator. See 4.8

8.1.6

4-pin Connector

Type: GH connector, 1.25mm pitch, 4 way. Mating connector housing: GHR-04V-S

Pin Name

Direction Level

Description

Comment

NRST

3V3_LVTTL Reset input

Directly connects to nRST_IN of internal mosaic,
see 4.1

TXD2

Out

3V3_LVTTL Serial COM2 transmit line

Directly connects to TXD2 of internal mosaic, see 4.3

RXD2

3V3_LVTTL Serial COM2 receive line

Directly connects to RXD2 of internal mosaic, see 4.3

GND

Ground

8.2

Accessories

The following accessories are delivered with mosaic-go:

Accessory

Comment

6-pin COM1 open-ended cable

GH connector in one side and open ended in other
side. See wire color code below.

4-pin COM2 open-ended cable

GH connector in one side and open ended in other
side. See wire color code below.

USB cable

Micro-B USB cable

Help user guide card

A small printed card which includes the basic how-to
guide and QR code to access Septentrio support
information.

Summary of Contents for mosaic Series


























































Search results

Summary of Contents for mosaic Series

Reviews:

Related manuals for mosaic Series

Brands by name

Popular brands

SEPTENTRIO mosaic Series, Hardware Manual

Search results

Summary of Contents for mosaic Series

Reviews:

Related manuals for mosaic Series

Brands by name

Popular brands