SEPTENTRIO mosaic Series Hardware Manual Download Page 9

Page: 9 / 57

mosaic GNSS Module

•

Ethernet (the PHY is external to the module). See section 4.5.

•

SDCard interface for logging to an external SD card. See section 4.6.

•

GPIO and LEDs output. See section 4.10.

The table below summarizes the main differences between the mosaic models in terms
of hardware features. The frequency bands in blue are supported.

mosaic
model

#Ants

Time &

Freq sync

Supported Frequency Bands per Antenna

mosaic-X5

mosaic-Sx

mosaic-T

Yes

mosaic-
CLAS

mosaic-H

mosaic-H can be configured in two different band plans,
applicable to both antennas:

By default, mosaic-H operates in band plan #1, with the
E5b/B2b/B2I band enabled. Band plan #2, with B3 enabled
instead of E5b/B2b/B2I, is selected when the BDSB3I signal is
enabled with the

setSignalTracking

user command.

Summary of Contents for mosaic Series


























































Search results

Summary of Contents for mosaic Series

Reviews:

Related manuals for mosaic Series

Brands by name

Popular brands

SEPTENTRIO mosaic Series, Hardware Manual

Search results

Summary of Contents for mosaic Series

Reviews:

Related manuals for mosaic Series

Brands by name

Popular brands