background image

 

       www.selwoodproducts.com

 

           

Warnings and Safe Play Instructions

CONTINUOUS ADULT SUPERVISION REQUIRED.

 Most serious injuries and deaths on playground equipment have occurred 

while children were unsupervised! Our products are designed to meet mandatory and voluntary safety standards. Complying 

with all warnings and recommendations in these instructions will reduce the risk of serious or fatal injury to children using 

this play system. Go over the warnings and safe play instructions regularly with your children and make certain that they 

understand and follow them. Remember on-site adult supervision is required for children of all ages.

   Observe capacity limitations of your play-set. See  

front cover.

   Dress children with well fitting and full foot enclosing 

footwear.

   Teach children to sit with their full weight in the center  

of the swing seat to prevent erratic swing motion or 

falling off.

   Check for splintered, broken or cracked wood; missing, 

loose, or sharp edged hardware. Replace, tighten and or 

sand smooth as required prior to playing.

   Verify that suspended climbing ropes, rope ladders, chain 

or cable are secured at both ends and cannot be looped 

back on itself as to create an entanglement hazard.

   On sunny and or hot days, check the slide and other 

plastic rides to assure that they are not very hot as to 

cause burns. Cool hot slide and rides with water and wipe 

dry prior to using.

   Do not allow children to wear open toe or heel footwear 

like sandals, flip–flops or clogs.

   Do not allow children to walk, in front, between, behind 

or close to moving rides.

   Do not let children twist swing chains or ropes or loop 

them over the top support bar. This may reduce the 

strength of the chain or rope and cause premature failure.

   Do not let children get off rides while they are in motion.

   Do not permit climbing on equipment when it is wet.

   Do not permit rough play or use of equipment in a 

manner for which it was not intended. Standing on or 

jumping from the roof, elevated platforms, swings, 

climbers, ladders or slide can be dangerous.

   Do not allow children to swing empty rides or seats.

   Do not allow children to go down slide head first or  

run up slide.

2

SERIOUS HEAD INJURY HAZARD

Installation over concrete, asphalt, dirt, grass, carpet 

and other hard surface creates a risk of serious injury 

or death from falls to the ground. Install and maintain 

shock absorbing material under and around play-set as 

recommended on page 3 of these instructions.

COLLISION HAZARD

Place play-set on level ground at least 6 feet from any 

obstruction such as a garage or house, fences, poles, 

trees, sidewalks, walls, landscape timbers, rocks, 

pavement, planters, garden borders, overhanging 

branches, laundry lines, and electrical wires. (See 

OBSTACLE FREE SAFETY ZONE on cover)

CHOKING HAZARD/SHARP EDGES & POINTS

Adult assembly required. This product contains small 

parts and parts with sharp edges and points. Keep parts 

away from children until fully assembled.

WARNING LABEL

Owners shall be responsible for maintaining the legibility 

of the warning labels.

STRANGULATION HAZARD

•  NEVER allow children to play with ropes, clotheslines, 

pet leashes, cables, chains or cord-like items when using 

this play-set or to attach these items to play-set.

•  NEVER allow children to wear loose fitting clothing, 

ponchos, hoods, scarves, capes, necklaces, items with 

draw-strings, cords or ties when using this play-set.

•  NEVER allow children to wear bike or sport helmets 

when using this play-set.

Failure to prohibit these items, even helmets with chin 

straps, increases the risk of serious injury and death to 

children from entanglement and strangulation.

TIP OVER HAZARD

Choose a level location for the equipment. This can reduce 

the likelihood of the play set tipping over and loose-fill 

surfacing materials washing away during heavy rains.

DO NOT allow children to play on the play-set until the 

assembly is complete and the unit is properly anchored.

WARNING

 

WARNING

 – Safe Play Instructions 

 

Summary of Contents for MEADOWSIDE II F24021E













































Reviews: