Seepex BN 17-12S Operating And Assembly Instruction Manual Download Page 58

Page: 58 / 86

9.2 Reassembly

A / 07.11.2019 - OM.SCT.BN.S03EN

25/36

Assemble holding band - drive-side

Damage of universal joint sleeve due to

sharp tools. Leak in universal joint sleeve.



Ventilate inner area of joint by lifting the universal
joint sleeve

(405)

–

Use a suitable tool

(WS)



Slide holding bands

(406, 407)

loosely onto

universal joint sleeve

(405)



Tighten holding band

(406, 407)

- drive-side.

–

Insert holding band

(406, 407)

into

tool

(W3)

–

Clamp holding band firmly using eccentric
lever

(EX)

–

Turn crank

(KUL)

until the holding band

(406, 407)

is tensioned and is in contact with

holding band loop

(SCL)

–

Carefully pull the holding band

(406, 407)

together until it is in contact with the
universal joint sleeve around the circumfer-
ence.

Correct

The holding band

(406, 407)

has drawn in the out

shape of the universal joint sleeve and is firmly
seated.

Summary of Contents for BN 17-12S























































































Search results

Summary of Contents for BN 17-12S

Reviews:

Related manuals for BN 17-12S

Brands by name

Popular brands

Seepex BN 17-12S, Operating And Assembly Instruction Manual

Search results

Summary of Contents for BN 17-12S

Reviews:

Related manuals for BN 17-12S

Brands by name

Popular brands