Seepex BN 17-12S Operating And Assembly Instruction Manual Download Page 49

Page: 49 / 86

9.2 Reassembly

A / 07.11.2019 - OM.SCT.BN.S03EN

16/36

Recommended special tools

Recommended auxiliary materials

Keep the auxiliary materials listed available (not included in the scope of
delivery):



Soft soap

(GS)



Anti-seize graphite petroleum

(GC)



SEEPEX joint grease

(GF)



Kinetic ring grease

(KF)

- SEEPEX BIO 10206

9.2.2 Prepare components parts for assembly

9.2.2.1 Prepare rotor head (640) for assembly



Remove any damage.



Clean rotor head

(640)

Special tools are not part of the delivery scope.



Order special tools using the order form (



chapter 11).

Illustration

Denomination

Packing puller

(W1)

Mounting tool

(W3)

Assembly mandrel

(W4)

Drift

(W5)

Mounting lever

(W9)

Dismantling tool

(W10)

NOTICE

Damage to property due to inadequate lubricants (GM).

Damage to components. Contamination of the conveying medium.



Observe resistance to the materials used and the conveying medium.



Use suitable lubricants

(GM)

only.

Summary of Contents for BN 17-12S























































































Search results

Summary of Contents for BN 17-12S

Reviews:

Related manuals for BN 17-12S

Brands by name

Popular brands

Seepex BN 17-12S, Operating And Assembly Instruction Manual

Search results

Summary of Contents for BN 17-12S

Reviews:

Related manuals for BN 17-12S

Brands by name

Popular brands