SeaLevel SeaI/O User Manual Download Page 38 | Manualshive

Page: 38 / 112

background image

38

© Sealevel Systems, Inc.

SeaI/O | SL9049 11/2021

Power Options

Base Module Power Connection

Base modules are powered from a 9-30VDC source using either the DC jack, screw terminals or the Expansion
pass-through connectors on the side of the unit. Sealevel offers several power supply choices to make
connection easy (see the Accessories chapter at the end of this document).

SeaI/O Expansion Power Connection

Each SeaI/O product, including the expansion modules, contains an onboard switching regulator power supply
rated for 9-

30VDC. For local installations (less than 10’ apart), expansion unit power is usually supplied from

the Base unit via the pass-through connectors. The number of expansion modules that can be driven from the
Base unit depends on the power source and number/type of expansion units. Refer to the chart below for

power requirements. For expansion modules mounted remotely (greater than 10’ apart), separate power is

required at each expansion unit. The output power available on the pass-through connector can only supply a
maximum of 1.2A to the additional units.

Supply power for expansion unites that are daisy-chained together should only have a single connection
to an external power supply made by only one expansion unit.

SeaI/O Max Power Requirements

W-Series

E-Series

U-Series

M-Series

S-Series

N-Series

SeaI/O-410

3.4W

2.9W

1.7W

1.4W

1.6W

1.4W

SeaI/O-420

4.0W

3.5W

2.3W

2.0W

2.2W

2.0W

SeaI/O-430

2.4W

1.9W

0.7W

0.4W

0.6W

0.4W

SeaI/O-440

4.5W

4.0W

2.8W

2.5W

2.7W

2.5W

SeaI/O-450

5.8W

5.3W

4.1W

3.8W

4.0W

3.8W

SeaI/O-470

3.5W

3.0W

1.8W

1.5W

1.7W

1.5W

SeaI/O-520

5.5W

5.0W

3.8W

3.5W

3.7W

3.5W

SeaI/O-530

3.4W

2.9W

1.7W

1.4W

1.6W

1.4W

SeaI/O-540

3.9W

3.4W

2.2W

1.9W

2.1W

1.9W

SeaI/O-570

4.3W

3.8W

2.6W

2.3W

2.5W

2.3W

SeaI/O-580

-

5.0W

-

-

-

-

SeaI/O-580PoE

-

5.0W

-

-

-

-

«
...
36
37
38
39
40
...
»

Summary of Contents for SeaI/O

















































































































Reviews:

No comments

Related manuals for SeaI/O

Brand: ABB Pages: 30

Brand: ABB Pages: 15

Brand: ABB Pages: 10

Brand: ABB Pages: 44

Brand: KAR-TECH Pages: 28

Brand: 2iB Pages: 5

Go!Control Panel

Brand: 2gig Technologies Pages: 78

7000-2 - Escalade RAID Controller

Brand: 3Ware Pages: 2

Brand: CALEFFI Pages: 12

QuickSetter+ 132 Series

Brand: CALEFFI Pages: 5

Brand: DayTronic Pages: 22

Brand: DayTronic Pages: 414

COOPER POWER SERIES

Brand: Eaton Pages: 50

Brand: Lamtec Pages: 22

Brand: Lawler Pages: 5

Brand: Pando Pages: 43

Brand: Bardiani Pages: 96

Brand: Eaton Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands