SeaLevel SeaI/O User Manual Download Page 10 | Manualshive

Page: 10 / 112

background image

10

© Sealevel Systems, Inc.

SeaI/O | SL9049 11/2021

SeaI/O Hardware Description

SeaI/O Base and Expansion Modules

Base Modules connect to the host via one of the following interfaces:

•

Wireless Gateway

–

Wireless Modbus TCP

•

W-Series

–

Wireless Modbus TCP

•

E-Series - Ethernet Modbus TCP

•

U-Series - USB Modbus RTU

•

M-Series - RS-485 Modbus RTU

•

S-Series - RS-232 Modbus RTU

After the base unit is installed, up to 246 additional SeaI/O N-Series Expansion Units

can be added to create an

I/O network. These expansion modules interface via RS-485 and can be located local to the Base SeaI/O device
or remotely located up to 4000 feet away. Local installations should use the 5

” CAT5 RS

-485 pass-through cable

(Part# CA239) shipped with each N-series module to connect. Remote expansion modules should use RS-485
twisted pair wiring from the base unit connected via the removable screw terminal connector.

For local installations, power to the expansion modules is supplied from the Base unit via the pass-through
connectors. For remote devices, separate power is required at each expansion unit. Refer to the

Power Options

section of this manual for more information on SeaI/O power requirements and power supply sizing.

«
...
8
9
10
11
12
...
»

Summary of Contents for SeaI/O

















































































































Reviews:

No comments

Related manuals for SeaI/O

Brand: Wavetec Pages: 17

Brand: Calsense Pages: 9

Smart Controller

Brand: MaestroHome Pages: 10

HomeTec Pro CFF3000

Brand: Abus Pages: 13

Brand: NAVITAS Pages: 7

Brand: Abus Pages: 2

Brand: IDTECK Pages: 12

Brand: Banner Pages: 2

CGLine+ Web Controller

Brand: Eaton Pages: 28

MT600iWP Series

Brand: weintek Pages: 2

Brand: L&L Pages: 16

Brand: Bardiani Pages: 22

Brand: U-Tron Pages: 8

Brand: Agilent Technologies Pages: 20

Brand: B meters Pages: 2

Brand: Samson Pages: 36

Brand: zeeltronic Pages: 15

Brand: M-system Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands