manualshive.com logo in svg

Sea Recovery SRC Aqua Matic 1400-2, Owner'S Manual, Page: 36 / 223

Share
Download
Sea Recovery SRC Aqua Matic 1400-2 Owner'S Manual Download Page 36

inches to ensure proper connection, relieve stress to the fitting and tube/hose, and allow easy detachment
and re-attachment during maintenance or repair.

1. Cut tube-end squarely and cleanly.

2. Loosen nut by three turns on the fitting.

3. Insert tube into the fitting until it bottoms.

4. Loosen nut completely and remove tube with attached parts from body.

5. Check that the O-Ring is seated under the tube's spacer, and not pinched into its body.

6. Insert tube with attached parts into the body and tighten nut finger-tight.

Interconnecting Components with Supplied Hose

Note:  ¼ in. (6.35 mm) OD, nylon tubing is supplied with applicable components for connecting pressure
pick-up points to the Low Pressure Transducers. Use of this tubing is dependent upon the optional Pre-filtration
components installed in your System.

Aqua Matic Compact 450-1800

34

Summary of Contents for SRC Aqua Matic 1400-2
































































































































































































































Reviews:

No comments