manualshive.com logo in svg

Sea-doo GTX DI 5649, Operator'S Manual

Share
Download
Sea-doo GTX DI 5649 Operator'S Manual Download Page 74

72

Engine Misfires, Runs Irregularly

Engine Overheats

Engine Continually Backfires

Engine Pinging or Knocking

OTHER OBSERVATION

POSSIBLE CAUSE

REMEDY

Weak spark.

• Fouled/defective/worn 

spark plugs.

Replace.

• Faulty rev limiter 

(

carburetor-equipped 

models

).

Refer to an authorized Sea-Doo 
dealer.

• Too much oil supplied to 

engine.

Improper oil pump adjustment, 
refer to an authorized Sea-Doo 
dealer.

Lean fuel mixture.

• Fuel: Level too low, stale or 

water-contaminated.

Siphon and/or refill.

• Fuel filter, clogged or water-

contaminated (

carburetor-

equipped models

).

Refer to an authorized Sea-Doo 
dealer.

• Fuel tank valve 

(

carburetor-equipped 

models

) partially open.

Turn fuel tank valve to ON position.

• Clogged injectors

(

DI models

).

Refer to an authorized Sea-Doo 
dealer.

• Defective sensor or MPEM 

(

DI models

).

Refer to an authorized Sea-Doo 
dealer.

Rich fuel mixture
(high fuel consumption).

• Flame arrester dirty/clogged

(

if so equipped

).

Clean or replace.

• Partially closed choke 

(

carburetor-equipped 

models

).

Refer to an authorized Sea-Doo 
dealer.

• Defective sensor or MPEM 

(

DI models

).

Refer to an authorized Sea-Doo 
dealer.

OTHER OBSERVATION

POSSIBLE CAUSE

REMEDY

Monitoring beeper sounds
continuously.

• Clogged jet pump water 

intake.

Clean.

• Clogged coolant system.

Flush cooling system.

OTHER OBSERVATION

POSSIBLE CAUSE

REMEDY

Weak spark.

• Fouled/defective/worn 

spark plugs.

Replace.

Overheated engine.

• See engine OVERHEATS.

Refer to an authorized Sea-Doo 
dealer.

• Faulty rev limiter 

(

carburetor-equipped 

models

).

OTHER OBSERVATION

POSSIBLE CAUSE

REMEDY

• Poor quality gasoline/low 

octane.

Use well known quality and 
recommended gasoline.

• Spark plug heat range too 

high.

Use recommended spark plugs.

• Ignition timing.

Refer to an authorized Sea-Doo 
dealer.

smo2000-003a.book Page 72 Thursday, November 11, 1999 10:44 AM

www.SeaDooManuals.net

Summary of Contents for GTX DI 5649




























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands