Sea-doo GTX DI 5649 Operator'S Manual Download Page 41

Page: 41 / 91

Shifter System

Check reverse gate operation for free
movement. With shift lever in forward
position, the gate should be in upward
position; locked on the

GTX DI mod-

els

and offering a resistance to go

downward on the

RX models

. With

the shift lever in neutral position, gate
should be in middle position. With shift
lever in reverse position, gate should
be in downward position.

VTS (Variable Trim System)
(if so equipped)

Push on arrows on VTS button to check
nozzle movement.

NOTE:

With the safety lanyard discon-

nected, electrical system can be acti-
vated for approximately 33 seconds by
depressing the engine start/stop button.

Safety Lanyard and Engine
Start/Stop Button

Position shift lever in neutral. Ensure
that both switches operate properly.
Start engine and stop it using each
switch individually.

Storage Compartment
Covers

Ensure they are closed and latched.



WARNING

Verify the reverse gate operation
before starting the engine.



WARNING

If engine does not shut-off when
pushing engine start/stop button
or by disconnecting the safety lan-
yard, stop the engine by applying
the choke and turning fuel tank
valve (

if so equipped

) to OFF posi-

tion. Do not operate the watercraft
further, see an authorized Sea-Doo
dealer.

smo2000-003a.book Page 39 Thursday, November 11, 1999 10:44 AM

www.SeaDooManuals.net

Summary of Contents for GTX DI 5649




























































































Search results

Summary of Contents for GTX DI 5649

Reviews:

Brands by name

Popular brands

Sea-doo GTX DI 5649, Operator'S Manual

Search results

Summary of Contents for GTX DI 5649

Reviews:

Brands by name

Popular brands