manualshive.com logo in svg

Sea-doo GTX DI 5649, Operator'S Manual

Share
Download
Sea-doo GTX DI 5649 Operator'S Manual Download Page 16

14

5. LIMITATIONS OF LIABILITY

This warranty gives you specific rights, and you may also have other legal rights resulting
from the application of mandatory national laws which may vary from country to country.

WHERE APPLICABLE, THIS WARRANTY IS EXPRESSLY GIVEN AND ACCEPTED IN
LIEU OF ANY AND ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING
WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR
ANY PARTICULAR PURPOSE.

In no event shall BOMBARDIER be liable for special, consequential or incidental damages,
including but not limited to loss of use and transportation costs.  Some countries do not
allow the exclusion or limitation of incidental or consequential damages, or limitations on
how long an implied warranty lasts, so the above limitation or exclusion may not apply.
Neither the SEA-DOO international distributor, the selling local authorized  SEA-DOO water-
crafts dealer nor any other person has been authorized to make any affirmation, representation
or warranty other than those contained in this warranty, and if made, such affirmation, repre-
sentation or warranty shall not be enforceable against BOMBARDIER or any other person.
Every SEA-DOO watercraft is sold with the English version of this warranty.  Some autho-
rized SEA-DOO International Distributor may elect to translate this warranty into local lan-
guage, it is then understood and agreed that in the event of any discrepancies or inconsis-
tencies between the two versions, the English version shall prevail.
It is the customer's responsibility to ensure that the SEA-DOO watercraft complies with
all boating regulations and standards of any country, other than the original country of sale,
where the SEA-DOO watercraft is intended to be used.
BOMBARDIER reserves the right to modify this warranty at any time, being understood
that such modification will not alter the warranty conditions applicable to the SEA-DOO
watercraft sold while this warranty is in effect.

6. TRANSFER

If the customer sells the SEA-DOO watercraft guaranteed under the present, he shall
assign and transfer this warranty, which shall be valid for the rest of the relevant PERIOD
as defined in section 1 hereinabove, to the new customer.

7. CONSUMER ASSISTANCE

a) In the event of a controversy or a dispute arising in connection with this BOMBARDIER

INTERNATIONAL LIMITED WARRANTY, BOMBARDIER suggests that you try to re-
solve the issue at the dealership level. We recommend discussing the issue with the
authorized dealer's service manager or owner.

b) If further assistance is required, the authorized local SEA-DOO INTERNATIONAL DIS-

TRIBUTOR's Service Department should be contacted in order to resolve the matter.

c) If the issue has still not been resolved, please submit in writing your complaint to:

BOMBARDIER INC.
RECREATIONAL PRODUCTS

CUSTOMER ASSISTANCE CENTER
75, J.-A. BOMBARDIER STREET
SHERBROOKE, QUEBEC
J1L 1W3
PHONE: (450) 532-5000

SEPTEMBER 1999
® Trademark of Bombardier Inc. and/or its subsidiaries

smo2000-003a.book Page 14 Thursday, November 11, 1999 10:44 AM

www.SeaDooManuals.net

Summary of Contents for GTX DI 5649




























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands