manualshive.com logo in svg

Sea-doo GTX DI 5649, Operator'S Manual

Share
Download
Sea-doo GTX DI 5649 Operator'S Manual Download Page 73

71

Engine Will Not Start

OTHER OBSERVATION

POSSIBLE CAUSE

REMEDY

Engine does not turn over.

• Safety lanyard removed.

Install cap over switch.

• Burnt fuse(s).

Check wiring then replace fuse(s).

• Discharged battery.

Refer to an authorized Sea-Doo 
dealer.

• Battery connections, 

corroded or loose.

Refer to an authorized Sea-Doo 
dealer.

• Water-flooded engine.

Refer to 

Water-Flooded Engine

 in 

SPECIAL PROCEDURES.

• MPEM  malfunction.

Refer to an authorized Sea-Doo 
dealer.

Engine turns slowly.

• Discharged or weak 

battery.

Refer to an authorized Sea-Doo 
dealer.

Engine turns normally.

• Closed fuel tank valve 

(

carburetor-equipped 

models

).

Turn fuel tank valve to ON position.

• Fuel tank empty or water-

contaminated.

Refill. Siphon and fill with fresh fuel.

• Fuel filter clogged or 

water-contaminated 
(

carburetor-equipped 

models

).

Clean, check fuel tank for water.

• Fouled/defective spark 

plugs.

Replace.

• Misuse of choke 

(

carburetor-equipped 

models

).

Use only with cold engine. Replace 
spark plugs.

• Fuel-flooded engine.

Refer to 

Fuel-Flooded Engine

 in 

SPECIAL PROCEDURES.

• Fuel rail/air compressor 

malfunction (

DI models

).

Refer to an authorized Sea-Doo 
dealer.

• Burnt fuel pump fuse

(DI models)

.

Check wiring then replace fuse.

• Electrical problem

(DI models)

.

Refer to an authorized Sea-Doo 
dealer.

smo2000-003a.book Page 71 Thursday, November 11, 1999 10:44 AM

www.SeaDooManuals.net

Summary of Contents for GTX DI 5649




























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands