manualshive.com logo in svg

Sea-doo GTX DI 5649, Operator'S Manual

Share
Download
Sea-doo GTX DI 5649 Operator'S Manual Download Page 29

27

Other Functions

The following describes how to select
other available functions.

Language Option

While in the clock/compass mode:

1. Press and hold for 2 seconds

1. Repeatedly press 

1. Press to end

English/Metric System

Allows to display the units in the met-
ric system or in the SAE English sys-
tem.

1. Press TOGETHER and hold for 2 seconds

Clock Adjustment

While in the clock/compass mode:

1. Press TOGETHER and hold for 2 seconds

1. Repeatedly press to adjust HOURS

1. Repeatedly press to adjust MINUTES

1. Press TOGETHER to end

NOTE:

 If MODE and SET buttons are

not pressed at the end, the default dis-
play will come back after 10 seconds
and the time entered will remain.

F00L2B0

1

F00L2BZ

1

F00L2B0

1

F00L2B1

1

F00L2B1

1

F00L2BZ

1

F00L2B0

1

F00L2B1

1

smo2000-003a.book Page 27 Thursday, November 11, 1999 10:44 AM

www.SeaDooManuals.net

Summary of Contents for GTX DI 5649




























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands