manualshive.com logo in svg

Sea-doo GTX DI 5649, Operator'S Manual

Share
Download
Sea-doo GTX DI 5649 Operator'S Manual Download Page 52

50

1. Grounding device

Remove both spark plugs and spray
BOMBARDIER LUBE lubricant or
equivalent into each cylinder.

Carburetor-Equipped Models

Crank the engine a few turns to distrib-
ute the oil on cylinder wall.

DI Models

To prevent fuel to be injected in the en-
gine and engine starting, proceed as
follows.

Depress the throttle lever at full throt-
tle position and HOLD for cranking.

Crank the engine a few turns to distrib-
ute the oil on cylinder wall.

All Models

Apply anti-seize lubricant on spark plug
threads then reinstall them.

Reinstall plug on air intake silencer cov-
er.

Properly reconnect spark plug cables
to spark plugs.

Wipe up any residual water from the
engine.

Anticorrosion Treatment

To prevent corrosion, spray a corrosion
inhibitor (salt water resistant) such as
BOMBARDIER LUBE lubricant or
equivalent over metallic components
in engine compartment.

Apply dielectric grease (salt water re-
sistant) on battery posts and cable
connectors.

CAUTION:

Never leave rags or tools

in the engine compartment or in the
bilge.

F07H0AY

1

WARNING

Always reconnect spark plug ca-
b les at the  sam e spark plugs
where they come from. The cable
coming out the edge of the electri-
cal box must be connected to the
MAG side spark plug.

smo2000-003a.book Page 50 Thursday, November 11, 1999 10:44 AM

www.SeaDooManuals.net

Summary of Contents for GTX DI 5649




























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands