manualshive.com logo in svg

Sea-doo GTX DI 5649, Operator'S Manual

Share
Download
Sea-doo GTX DI 5649 Operator'S Manual Download Page 61

59

Throttle and Choke Cable 
Inspection

Throttle Cable

Depress and release the throttle lever.
It should operate smoothly and return
to its initial position without any hesi-
tation. Refer to an authorized Sea-Doo
dealer if necessary.

Carburetor-Equipped Models

Do not activate throttle lever unneces-
sarily, when engine is not running. Car-
buretors are equipped with fuel accel-
erator pumps. These pumps deliver
fuel to the engine each time throttle
lever is depressed.

All Models

1. Should move freely

Carburetor-Equipped Models

Choke Cable

Ensure choke cable operates smooth-
ly and without any hesitation from fully
opened to fully closed. When the
choke lever is fully pulled, choke
should be fully applied. Refer to an au-
thorized Sea-Doo dealer if necessary.

Carburetor Adjustment

Carburetor adjustment is very impor-
tant to allow good engine operation and
therefore watercraft performance. Car-
buretor adjustment requires technical
knowledge and experience to have the
correct mixture supplied to the engine.

CAUTION:

Serious engine damage

can occur with improper carburetor
adjustment.

Fuel Injection System 

DI Models

The fuel injection system inspection
should be performed by an authorized
Sea-Doo dealer.

CAUTION:

Never use injector clean-

ing products. They may contain ad-
ditives that could damage injector
components.

All Models

Fuel and Oil Filters

The fuel filter (

carburetor-equipped

models

) and the oil filter should be re-

placed by an authorized Sea-Doo deal-
er. 

Fuel system pressurization

 should

be conducted at the same time.

CAUTION:

An obstructed oil filter

will cause oil starvation resulting in
serious engine damage.

Steering Alignment

When the handlebar is directed in
straight ahead position, the jet pump
nozzle should be in the same direction
allowing the watercraft to run in a
straight line.

Refer to an authorized Sea-Doo dealer
if an adjustment is necessary.

 WARNING

Do not alter or tamper with throt-
tle cable adjustment or routing.

WARNING

If throttle lever does not automat-
ically return, do not operate

 

water-

craft

 

and see your authorized Sea-

Doo dealer.

F01K01Y

1

WARNING

E nsure the h andlebar and  jet
pump nozzle operate freely from
side to side and are not stressing
the steering cable or brackets.

smo2000-003a.book Page 59 Thursday, November 11, 1999 10:44 AM

www.SeaDooManuals.net

Summary of Contents for GTX DI 5649




























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands