manualshive.com logo in svg

Sea-doo 2003 LRV DI, Operator'S Manual, Page: 74 / 88

Share
Download
Sea-doo 2003 LRV DI Operator'S Manual Download Page 74

72

Engine Will Not Start

Engine Misfires, Runs Irregularly

OTHER OBSERVATION

POSSIBLE CAUSE

REMEDY

Engine does not turn over. • Safety lanyard removed.

Install cap over post.

• Burnt  fuse  on  MPEM  or  in  rear

electrical box: battery, starting
system, fuel pump.

Check wiring then replace fuse(s).

• Discharged battery.

Refer to an authorized SEA-DOO
dealer.

• Battery connections, corroded or

loose.

Refer to an authorized SEA-DOO
dealer.

• Water-flooded engine.

Refer to WATER-FLOODED EN-
GINE in SPECIAL PROCEDURES.

• Faulty sensor or MPEM.

Refer to an authorized SEA-DOO
dealer.

• Seized engine.

Refer to an authorized SEA-DOO
dealer.

• Seized jet pump.

Try to clean. Otherwise, refer to an
authorized SEA-DOO dealer.

Engine turns slowly.

• Loose battery cable connections.

Check/clean/tighten.

• Discharged or weak battery.

Refer to an authorized SEA-DOO
dealer.

• Worn starter.

Refer to an authorized SEA-DOO
dealer.

Engine turns normally.

• Fuel tank empty or water-

contaminated.

Refill. Siphon and fill with fresh fuel.

• Fouled/defective spark plugs.

Replace.

• Faulty component in the fuel in-

jection system.

Refer to an authorized SEA-DOO
dealer.

• Burnt fuel pump fuse.

Check wiring then replace fuse.

• Electrical problem.

Refer to an authorized SEA-DOO
dealer.

OTHER OBSERVATION

POSSIBLE CAUSE

REMEDY

Weak spark.

• Fouled/defective/worn spark 

plugs.

Replace.

• Faulty MPEM.

Refer to an authorized SEA-DOO
dealer.

• Too much oil supplied to en-

gine.

Improper oil pump adjustment,
refer to an authorized SEA-DOO
dealer.

Lean fuel mixture.

• Fuel: Level too low, stale or

water-contaminated.

Siphon and/or refill.

• Clogged injectors.

Refer to an authorized SEA-DOO
dealer.

• Defective sensor or MPEM.

Refer to an authorized SEA-DOO
dealer.

Rich fuel mixture
(high fuel consumption).

• Flame arrester dirty/clogged

(

if so equipped

).

Clean or replace.

• Defective sensor or MPEM.

Refer to an authorized SEA-DOO
dealer.

smo2003-005a.book  Page 72  Friday, November 1, 2002  8:25 AM

Summary of Contents for 2003 LRV DI

























































































Reviews:

No comments