manualshive.com logo in svg

Sea-doo 2003 LRV DI, Operator'S Manual, Page: 31 / 88

Share
Download
Sea-doo 2003 LRV DI Operator'S Manual Download Page 31

29

The information center includes the fol-
lowing display areas.

1. General display
2. Message/units display
3. Warning light
4. Fuel level display
5. VTS position indicator (

if so equipped

)

General Display

The default display is the clock (or
clock/compass 

if so equipped

) unless

another mode has been selected. See

Display Priorities

 below.

Repeatedly pressing the MODE button
scrolls the following displays: Tachom-
eter, speedometer, average speed, trip
meter, hourmeter, water temperature,
exterior temperature (

if so equipped

)

and chronometer.

1. Press to change display mode

When you are satisfied with your choice,
stop pressing the button.

Clock:

 Indicates the actual time in hours

and minutes (hh:mm).

Clock/Compass (

if so equipped

):

 Dis-

plays the cardinal points to indicate the
orientation of the watercraft.

Tachometer:

 Indicates the revolutions

per minute (RPM) of the engine. 

Speedometer:

 Indicates the speed of

watercraft in kilometers per hour (KPH)
or miles per hour (MPH).

Average Speed:

 The information cen-

ter approximately calculates and dis-
plays the average speed (AV KPH or
AV MPH) of the watercraft since the
last engine start.

Trip Meter:

 The information center ap-

proximately calculates the distance
based on the operation time and the wa-
tercraft speed and displays the result in
kilometers (KM) or miles (MILES).

Hourmeter:

 Displays the time in hours

of the watercraft usage.

Water Temperature:

 Displays the wa-

ter temperature (L TEMP) in degrees
Celsius (°C) or Farenheit (°F).

Exterior Temperature (

if so equipped

):

Displays the exterior air temperature
(E TEMP) in degrees Celsius (°C) or Fahr-
enheit (°F).

Chronometer:

 Allows to measure an

interval of time in hours and minutes
(hh:mm).

F00L2CY

3

4

5

1

2

F00L2BZ

1

WARNING

Use the compass as a guide only.
Not to be used for navigation pur-
poses.

smo2003-005a.book  Page 29  Friday, November 1, 2002  8:25 AM

Summary of Contents for 2003 LRV DI

























































































Reviews:

No comments