Sea-doo 2003 LRV DI Operator'S Manual Download Page 70

Page: 70 / 88

Hose Disconnection

Disconnect water

INLET

hose at engine

between T-fitting and cylinder head fit-
ting.

1. Disconnect this side of the T-fitting

Temporarily install a short piece of hose
to replace the one removed.

Antifreeze

Insert a funnel into the temporary hose
and pour antifreeze mix in engine until
the colored solution appears at cooling
system bleed outlet.

At this point, install a hose pincher on
bleed outlet hose.

1. Bleed outlet hose

Continue to pour until antifreeze flows
in air compressor water outlet hose.

1. Air compressor water outlet hose

Remove pinchers in this order to allow
proper flow of antifreeze.

1. Bleed outlet hose.

2. Crankcase cooling cover outlet hose.

3. Engine cylinder drain hose.

4. Water outlet hose.

F12E0BY

F07E0LY

F07E0OY

F07E0NX

smo2003-005a.book Page 68 Friday, November 1, 2002 8:25 AM

Summary of Contents for 2003 LRV DI

























































































Search results

Summary of Contents for 2003 LRV DI

Reviews:

Sea-doo 2003 LRV DI, Operator'S Manual, Page: 70 / 88

Search results

Summary of Contents for 2003 LRV DI

Reviews: