manualshive.com logo in svg

Sea-doo 2003 LRV DI, Operator'S Manual, Page: 35 / 88

Share
Download
Sea-doo 2003 LRV DI Operator'S Manual Download Page 35

33

12) Front Storage 

Compartment Cover 
Latch

Pull the latch lever upward in order to
open the front storage compartment
cover. Always relatch.

NOTE:

Verify periodically the lock pin

tightness of storage cover. Tighten if
needed and make sure storage cover
latches properly.

13) Side Storage 

Compartments

Two convenient watertight compart-
ments to carry personal articles. Ideal
location for water skis or wakeboards.

Left side storage compartment is also
provided with a holder. Tool kit is insert-
ed in that holder.

14) Underseat Storage 

Compartments

Convenient watertight, removable bas-
ket to carry personal articles. Remove
seat to gain access to underseat stor-
age compartments.

15) Tool Kit

Contains tools needed to perform basic
watercraft maintenance.

16) Air Intake Opening

This is where air enters to supply the
engine and to ventilate the engine com-
partment. If the air intake opening is
kept under water, water will get inside
bilge.

CAUTION:

If the air intake opening

is kept under water, such as turning
constantly in tight circles, water will
get inside bilge, which may cause
severe damage to internal parts of
the engine.

17) Seat Strap

The seat strap provides a handhold to
assist boarding and is used as a hand-
hold for the passenger.

18) Seat Latch

Removing the seat allows access to
the engine compartment.

The seat latch is located at the rear end
and underneath the seat.

TYPICAL

1. Seat latch

To remove seat, pull the latch lever up-
ward and hold. Lift and pull the seat
rearward.

NOTE:

It is necessary to remove the

seat extension first and repeat the
same procedure to remove the seat.

 WARNING

Never leave any heavy or break-
able objects loose in the storage
compartment. Never operate the
craft with the storage compart-
ment cover open.

 WARNING

Never leave any heavy or break-
able objects loose in the storage
compartment. Never operate the
craft with the storage compart-
ment cover open.

1

F17L0EY

smo2003-005a.book  Page 33  Friday, November 1, 2002  8:25 AM

Summary of Contents for 2003 LRV DI

























































































Reviews:

No comments