manualshive.com logo in svg

Sea-doo 2003 LRV DI, Operator'S Manual, Page: 30 / 88

Share
Download
Sea-doo 2003 LRV DI Operator'S Manual Download Page 30

28

From the forward position, pull the le-
ver to reverse. Push back to go to for-
ward. Always set in forward when fin-
ished. To find the neutral, set in
reverse then push back until the wa-
tercraft stops moving backwards.

TYPICAL — FORWARD POSITION

TYPICAL — NEUTRAL POSITION

TYPICAL — REVERSE POSITION

6) Speedometer

Analog speedometer indicates the
speed of watercraft in miles per hour
(MPH) and kilometers per hour (km/h).

The speed sensor mounted on the ride
plate sends the signal to the speedom-
eter and information center.

7) Information Center 

Gauge/Buttons
(if so equipped)

NOTE:

With the safety lanyard discon-

nected, information center can be ac-
tivated for approximately 33 seconds
by depressing the engine start/stop
button. This is convenient to see the
fuel level or view some other functions
when the safety lanyard is not at hand.

This is a LCD multifunction gauge. Dif-
ferent displays and functions can be
activated using 2 buttons — MODE
and SET — following specific sequenc-
es as described below.

1. To change display mode
2. To set or reset a function

Resetting a Function

To reset a function (such as the chro-
nometer, distance, etc.) press and hold
the SET button for 2 seconds while in
the appropriate mode.

F17L0AY

F17L0BY

F17L0CY

F00L2BY

1

2

smo2003-005a.book  Page 28  Friday, November 1, 2002  8:25 AM

Summary of Contents for 2003 LRV DI

























































































Reviews:

No comments