manualshive.com logo in svg

Sea-doo 2003 LRV DI, Operator'S Manual, Page: 67 / 88

Share
Download
Sea-doo 2003 LRV DI Operator'S Manual Download Page 67

65

TRAILERING, STORAGE
AND PRE-SEASON PREPARATION

Trailering

Make sure that oil reservoir and fuel
tank caps are properly installed.

 

Check the applicable laws and regula-
tions in your area concerning towing a
trailer, especially the following rules:

– brake system

– tow vehicle weight

– mirrors.

Take the following precautions when
towing the watercraft:

Tie the watercraft to both bow and
stern (front/rear) eyelets so that it is
firmly retained on the trailer. Use addi-
tional tie-downs if necessary.

CAUTION:

Do not route ropes or tie-

downs over the seat as they could
produce permanent damage. Wrap
ropes or tie-downs with rags or sim-
ilar protectors where they can touch
the

 

watercraft

 

body.

Ensure all storage compartment cov-
ers and seat are properly latched.

A SEA-DOO cover can protect the wa-
tercraft, particularly before driving on
dirt roads, to prevent dirt entry through
the air intake opening(s).

Observe trailering safety precautions.

Launching/Loading

CAUTION:

Before launching the wa-

tercraft, ensure the bilge plugs are
fully screwed. After loading the wa-
tercraft, ensure they are removed to
drain bilge.

Storage

It is recommended that the watercraft
be serviced by an authorized SEA-DOO
dealer for storage but the following op-
erations can be performed by you with
a minimum of tools.

CAUTION:

Do not run the engine dur-

ing the storage period.

Engine Draining

Check engine drain hose

 

(lowest hose

of engine). Make sure there is no sand
or other particles in it and that it is not
obstructed so that water can exit the
engine. Clean hose and fitting as nec-
essary.

CAUTION:

Water in engine drain hose

should be free to flow out, otherwise
water could be trapped in engine.
Should water freeze in engine, se-
vere damage will occur. Check en-
gine drain hose for obstructions.

Disconnect the quick connect fitting.
Press both tabs and pull fitting.

 WARNING

Never tip this vehicle on end for
transporting. We recommend that
you carry the vehicle in its normal
operating position.

WARNING

Make sure seat is securely latched
before prior to trailering.

 WARNING

Because fuel and oil are inflamma-
ble, have an authorized SEA-DOO
dealer inspect the fuel and oil sys-
tems integrity as specified in the
periodic inspection chart.

smo2003-005a.book  Page 65  Friday, November 1, 2002  8:25 AM

Summary of Contents for 2003 LRV DI

























































































Reviews:

No comments