Sea-doo 2001 GS 5548 Operator'S Manual Download Page 6

Page: 6 / 100

SPECIAL PROCEDURES..............................................................

Engine Overheating .................................................................................

Jet Pump Water Intake and Impeller Cleaning ........................................

Capsized Watercraft ................................................................................

Submerged Watercraft ............................................................................

Water-Flooded Engine .............................................................................

Fuel-Flooded Engine ................................................................................

Towing the Watercraft in Water ..............................................................

Low-Charge Battery Condition ................................................................

MAINTENANCE ..........................................................................

Lubrication ...............................................................................................

Periodic Inspection ..................................................................................

Periodic Inspection Chart.........................................................................

Throttle and Choke Cable Inspection.......................................................

Carburetor Adjustment ............................................................................

Fuel and Oil Filters...................................................................................

Steering Alignment..................................................................................

VTS Adjustment (if so equipped) .............................................................

Vacuum Bailer Pick-Ups...........................................................................

Water Tank Trap Drains ...........................................................................

Fuses .......................................................................................................

General Inspection and Cleaning .............................................................

TRAILERING, STORAGE AND PRE-SEASON PREPARATION.......

Trailering ..................................................................................................

Storage ....................................................................................................

Pre-Season Preparation ...........................................................................

TROUBLESHOOTING ..................................................................

SPECIFICATIONS ........................................................................

SI METRIC INFORMATION ..........................................................

ABBREVIATIONS USED IN THIS MANUAL .................................

CHANGE OF ADDRESS...............................................................

smo2001-002a.book Page 4 Wednesday, June 7, 2000 3:57 PM

www.SeaDooManuals.net

Summary of Contents for 2001 GS 5548





































































































Search results

Summary of Contents for 2001 GS 5548

Reviews:

Related manuals for 2001 GS 5548

Brands by name

Popular brands

Sea-doo 2001 GS 5548, Operator'S Manual

Search results

Summary of Contents for 2001 GS 5548

Reviews:

Related manuals for 2001 GS 5548

Brands by name

Popular brands