Sea-doo 2001 GS 5548 Operator'S Manual Download Page 32

Page: 32 / 100

Multifunction Gauge Operation

Display Priorities

The clock/compass function is the ba-
sic mode of the Info Center gauge.

Use the compass as a guide only.
Not to be used for navigation pur-
poses.

The chronometer, tachometer and
speedometer are the only other modes
that may be chosen to replace the
clock/compass mode.

If another mode is chosen, the clock/
compass mode will be displayed again
after 4 seconds.

The Info Center also features a red
warning LED (Light-Emitting Diode)
which blinks whenever one of the fol-
lowing circumstances occur: engine
overheating, low fuel, low oil and low
voltage.

For example, if the fuel level is low, the
LED and the message LOW FUEL will
blink.

As a self test, all LCD segments and
the LED will turn on for 3 seconds each
time the watercraft is started.

In the event of a warning message
such as low fuel, hi-temp, etc., the
message will blink and override all oth-
er display functions.

If more than one warning message oc-
curs, the messages will blink and reap-
pear every 4 seconds.

Scrolling Functions

Press the MODE button until the de-
sired function is displayed on the Info
Center gauge.

Reset a Function

To reset a function such as the chro-
nometer, peak speed, distance, etc.,
press and hold the SET button for 2
seconds while in the appropriate mode.

Language Option

While in the clock/compass mode,
press and hold the SET button for at
least 2 seconds. Language option will
be displayed.

Press the MODE button to scroll lan-
guage (English, French and Spanish).

Press the SET button to confirm the
desired language and return to the
clock/compass mode.

English/Metric Option

Press and hold both MODE and SET
buttons for at least 2 seconds. The
system will be automatically changed.

Chronometer

While in the chronometer mode, press
the SET button to start and stop the
chronometer.

Press the SET button for 2 seconds to
reset the chronometer.

Clock Adjustment

While in the clock/compass mode, press
and hold the MODE and SET buttons for
2 seconds.

Press the MODE button to adjust the
hours and the SET button to adjust the
minutes.

Press again on the MODE and SET
buttons to return to the normal mode
(or it will return to the normal mode af-
ter 10 seconds).

Maintenance Information

When the watercraft is due for a mainte-
nance inspection, the message MAINT
will blink.

To clear the warning message, press
the SET button for 2 seconds during
the message blinking.

11) Glove Box

(if so equipped)

A small, convenient watertight storage
compartment for gloves, keys, wallet,
maps, etc.

smo2001-002a.book Page 30 Wednesday, June 7, 2000 3:57 PM

www.SeaDooManuals.net

Summary of Contents for 2001 GS 5548





































































































Search results

Summary of Contents for 2001 GS 5548

Reviews:

Related manuals for 2001 GS 5548

Brands by name

Popular brands

Sea-doo 2001 GS 5548, Operator'S Manual

Search results

Summary of Contents for 2001 GS 5548

Reviews:

Related manuals for 2001 GS 5548

Brands by name

Popular brands